suspect-devices/circuitpython/shared-bindings, branch 0.10.0CircuitPython - a Python implementation for teaching coding with microcontrollershttps://git.suspectdevices.com/suspect-devices/circuitpython/atom?h=0.10.02017-05-16T02:52:38+00:00atmel-samd: Support wav file playback. Tested up to 16bit 22.1khz. Must be mono file!2017-05-16T02:52:38+00:00Scott Shawcroftscott.shawcroft@gmail.com2017-05-11T01:21:02+00:00urn:sha1:3f5028c666008f58785e86dd477065e3ca99d99f
SD card support may work but likely needs buffer tuning. Its untested.
Fixes #105
shared-bindings: Correct PulseIn.resume to match docs. Fixes #1252017-05-08T18:14:23+00:00Scott Shawcroftscott.shawcroft@gmail.com2017-05-08T18:14:23+00:00urn:sha1:ef1a4847b3ac445b1e02f4252a617aa2f5d0da17atmel-samd: Introduce audio sample playback via audioio.AudioOut.2017-05-01T20:10:03+00:00Scott Shawcroftscott.shawcroft@gmail.com2017-04-21T21:43:03+00:00urn:sha1:58b9789d0c824c665db744ef3653d6304e908bc0Switch to a shared piece of code to compute start and length of a2017-04-20T18:24:05+00:00Scott Shawcroftscott.shawcroft@gmail.com2017-04-20T18:24:05+00:00urn:sha1:939c0045dbf2694a12432ad861db166ecf483b67
buffer from start, end and length. The old code miscomputed length
leading to writing and reading from memory past the end of the buffer.
Consolidating the code should make it easier to get right everywhere.
Correct PulseOut example code2017-04-14T00:52:13+00:00Scott Shawcroftscott.shawcroft@gmail.com2017-04-14T00:52:13+00:00urn:sha1:b653c3c8fc2f97fa59f7d767338e2eab08739d57atmel-samd: Rework status LED implementation2017-04-12T22:24:50+00:00Scott Shawcroftscott.shawcroft@gmail.com2017-04-12T22:24:50+00:00urn:sha1:4a4f29b8f95aa67f63397ae4efe78c6994398ccf
* Track status pin use by user code separately so it can take over the pins and then give them back.
* Switch to hardware SPI for APA102 on Gemma and Trinket.
* Merge microcontroller/types.h into microcontroller/Pin.h to better match approach going forwards.
Split up nativeio.2017-04-10T20:32:19+00:00Scott Shawcroftscott.shawcroft@gmail.com2017-04-10T20:32:19+00:00urn:sha1:f28f8ba56809fd56e777eabceae21127f95b89ed
This was done to allow greatly granularity when deciding what functionality
is built into each board's build. For example, this way pulseio can be
omitted to allow for something else such as touchio.
Add low-level OneWire support class.2017-03-25T12:04:49+00:00Scott Shawcroftscott.shawcroft@gmail.com2017-03-25T12:04:49+00:00urn:sha1:ff208d767741104f7d2644a58269d7064d4c1b6a
This class focuses on the timing sensitive parts of the protocol.
Everything else will be done by Python code.
This also establishes that its OK to back a nativeio class with a
bitbang implementation when no hardware acceleration exists. When
it does, then bitbangio should be used to explicitly bitbang a
protocol.
Add PulseIn support which can be used to measure a series of pulse widths.2017-03-24T10:30:15+00:00Scott Shawcroftscott.shawcroft@gmail.com2017-03-13T20:55:11+00:00urn:sha1:7cb54864aa7c651fc65350708afcddfab2a15fcc
This is useful for infrared input and DHT sensors.
Add PulseOut which can pulse a PWMOut for IR remote transmission.2017-03-10T18:17:54+00:00Scott Shawcroftscott.shawcroft@gmail.com2017-03-10T18:17:54+00:00urn:sha1:d200a621647aa9fc05aae29ad7bc38363025438b