suspect-devices/circuitpython/stmhal/boards/PYBV4, branch esp-extra-scriptsCircuitPython - a Python implementation for teaching coding with microcontrollershttps://git.suspectdevices.com/suspect-devices/circuitpython/atom?h=esp-extra-scripts2016-05-13T10:01:21+00:00stmhal/led: Allow LEDs to be in PWM mode with TIM1 and channels 1-4.2016-05-13T10:01:21+00:00Damien Georgedamien.p.george@gmail.com2016-05-13T10:01:21+00:00urn:sha1:1dc2862a837a08c6aa96fb369657be21043015ad
This allows PYBv3 to use PWM for LED(1) and LED(2).
stmhal/diskio: Introduce MICROPY_HW_HAS_FLASH setting.2016-02-06T13:07:01+00:00Paul Sokolovskypfalcon@users.sourceforge.net2016-02-06T12:48:58+00:00urn:sha1:97a0846af906cde677742bff810fb7965c38fbb7
To allow to reuse stmhal/diskio for ports which don't have flash but have
other storage devices.
stmhal: Add PWM capability for LED(3) and LED(4) on pyboards.2016-01-29T22:44:43+00:00Damien Georgedamien.p.george@gmail.com2016-01-29T22:44:43+00:00urn:sha1:a8a4b01af6501ff7ab61b251fc30fcf8a286f8d1
USB CDC no longer needs TIM3 (which was originally used for LED(4) PWM)
and so TIM3 has been freed for general purpose use by the user. Hence
LED(4) lost its PWM capabilities.
This patch reinstates the PWM capabilities using a semi-generic piece
of code which allows to configure a timer and PWM channel to use for any
LED. But the PWM capability is only configured if the LED is set to an
intensity between 1 and 254 (ie only when needed). In that case the
relevant timer is configured for PWM. It's up to the user to make sure
the timers are not used if PWM is active.
This patch also makes sure that PWM LEDs are turned off using standard
GPIO when calling led.off() or led.intensity(0), instead of just setting
the PWM counter to zero.
stmhal: For SPI config, use HW_SPIx_SCK instead of HW_ENABLE_SPIx.2015-12-12T15:02:02+00:00Damien Georgedamien.p.george@gmail.com2015-12-12T15:02:02+00:00urn:sha1:f7c4f9a64048bcbeaf36be8590b352bbef72aa08
Previously, SPI was configured by a board defining MICROPY_HW_ENABLE_SPIx
to 0 or 1. Now, the board should define MICROPY_HW_SPIx_SCK, MISO, MOSI
and NSS. This makes it the same as how I2C is configured.
stmhal: Update PYBv3 and PYBv4 pin defs to include MMA pins, and others.2015-10-31T11:14:15+00:00Damien Georgedamien.p.george@gmail.com2015-10-31T11:14:15+00:00urn:sha1:f705cb5f7a755f4c370af8ec0ef659a2ee8e948dstmhal: Make accel AVDD pin configurable via mpconfigboard.h.2015-10-29T22:40:42+00:00Damien Georgedamien.p.george@gmail.com2015-10-29T22:40:42+00:00urn:sha1:6f70283909a718ca4eab4efcdd1a2d74939c7193stmhal: Use CMSIS_MCU definition from mpconfigboard.mk2015-08-07T07:54:14+00:00Dave Hylandsdhylands@gmail.com2015-08-06T07:03:45+00:00urn:sha1:872f9af6aed49fa088d89152b983506285e1d34b
This needs to land afte #1407 lands, since #1407 is where
the CMSIS_MCU was defined.
stmhal: Generate modstm constants per build2015-08-07T07:46:43+00:00Dave Hylandsdhylands@gmail.com2015-08-02T17:42:09+00:00urn:sha1:be66a9ecf60eac18e08eda7bddf4b3481459c9f2
This causes unnecessary constants to no longer be generated.
Some constants (like UART_BRR) are different between the F4 and F7
stmhal: Update Makefile and board configs to compile with relocated hal.2015-07-20T11:30:18+00:00Damien Georgedamien.p.george@gmail.com2015-07-19T11:17:42+00:00urn:sha1:a39df51d8ab9137b5852595a26d9aa072b46a697stmhal: Allow to name SPI busses, and give them names for pyboard.2015-05-27T16:21:42+00:00Damien Georgedamien.p.george@gmail.com2015-05-27T16:21:42+00:00urn:sha1:70446f46c2a970026c422b165853eda9dcbc10aa