1 files changed, 122 insertions, 0 deletions
diff --git a/Arduino/ems/keywords.h b/Arduino/ems/keywords.h
new file mode 100755
index 0000000..6e9c6e8
--- /dev/null
+++ b/Arduino/ems/keywords.h
@@ -0,0 +1,122 @@
+
+/*---------------------------------------------------------------------kewords.h
+ * Copyright 2012-2018 Donald Delmar Davis, Suspect Devices. All Rights Reserved
+ *
+ * !!!!!!!!!!!! ..... This may or may not be free software ..... !!!!!!!!!!!!!!!
+ *
+ * This file is autogenerated and while created by and needed for several open
+ * source modules the vocabulary is specific to the project and the routines
+ * referenced will be liscenced on a per project basis
+ *----------------------------------------------------------------------------*/
+
+/*----------------------------- Monitor keywords--------------------------------
+* The idea here is to create an automation freindly monitor protocol and debug
+* interfacse. Because this needs to be efficient (and flexible) I have chosen a
+* very simple interface which will access and may manipulate the devices public
+* variables.
+*
+* Basic Syntax for the monitor is
+* XXX[?!:] <variable stuff> <CR>
+* where:
+* XXX is a 3 letter command or variable.
+* ! execute command or store value
+* ? request a value
+* : value sent as a response or an update.
+* simple example
+* (reboot device)
+* RST!
+* (set red led value)
+* RED!255
+* RED:255
+* (request pressure sensor, recieve sensor value
+*  note: unsolicited temperature sensor update )
+* PS1?
+* PS1:1240.2
+* TS1:150.5
+*
+*/
+#ifndef keywords_h
+#define keywords_h
+
+
+#define HELPTEXT\
+"SYN[!  ]sync (hello)    "\
+"ACK[ : ]acknowlege(yes) "\
+"NAK[ : ]negative (no)   "\
+"SWV[ :?]Software Vers.  "\
+"HWV[ :?]Hardware Vers.  "\
+"GIT[ :?]GIT Repo Vers.  "\
+"MEM[ :?]Avaliable Mem.  "\
+"SSN[ :?]Unit Serial No. "\
+"HLP[ :?]help            "\
+"FTL[!: ]Fatal Error     "\
+"ALT[!: ]Alert           "\
+"WAR[!: ]Warning         "\
+"INF[!: ]Info            "\
+"DBG[!: ]Debugging Info  "\
+"LOG[!: ]Log             "\
+"STC[!:?]State Change    "\
+"DVL[!:?]Display Level   "\
+"LVL[!:?]Log Level       "\
+"RST[!  ]Reboot          "\
+"BLD[!  ]Reboot to loader"\
+"STP[!:?]Sim/Chk  E-Stop "\
+"LCS[!:?]Light Curt. Stop"\
+"LCR[!: ]Light Curt. Rst "\
+"NOW[!:?]Time as an int  "\
+"TIM[!:?]Time for humans "\
+"TS1[ :?]Temp Sensor 1   "\
+"TS2[ :?]Temp Sensor 2   "\
+"TMP[ :?]Temp Setting    "\
+"AMT[ :?]Ambient Temp    "\
+"AMH[ :?]Ambient Humidity"\
+"RED[!: ]Led (0-255)     "\
+"HSW[!:?]Heaters (ON/OFF)"\
+"H1S[!:?]Heater 1(ON/OFF)"\
+"H1V[!:?]Heater 1 (0-255)"\
+"H1P[!:?]Heater 1 P value"\
+"H1I[!:?]Heater 1 I value"\
+"H1D[!:?]Heater 1 D value"\
+"H2S[!:?]Heater 1(ON/OFF)"\
+"H2V[!:?]Heater 1 (0-255)"\
+"H2P[!:?]Heater 2 P value"\
+"H2I[!:?]Heater 2 I value"\
+"H2D[!:?]Heater 2 D value"\
+"PMS[!:?]Pump Sw (ON/OFF)"\
+"PSP[ :?]Pressure P value"\
+"PSI[ :?]Pressure I value"\
+"PSD[ :?]Pressure D value"\
+"PS1[ :?]Pressure Sensor "\
+"MUP[!: ]Manual up       "\
+"MDN[!: ]Manual down     "\
+"TMS[!:?]Timer setting   "\
+"TMR[!:?]Timer Run(ON/OF)"\
+"TRM[ :?]Time Remaining  "\
+"SOL[!:?]Solenoid(ON/OFF)"\
+"HOM[ :?]Home Switch     "\
+"CMD[!:?]Command Mode    "\
+"MLD[!:?]Enable Multiline"\
+"SOD[!: ]Start Multiline "\
+"EOD[!: ]End Multiline   "\
+"NOP[!: ]Not implemented"
+
+
+#define KEYWORDS \
+"SYN" "ACK" "NAK" "SWV" "HWV" "GIT" "MEM" "SSN" "HLP" "FTL" "ALT" "WAR" "INF" \
+"DBG" "LOG" "STC" "DVL" "LVL" "RST" "BLD" "STP" "LCS" "LCR" "NOW" "TIM" "TS1" \
+"TS2" "TMP" "AMT" "AMH" "RED" "HSW" "H1S" "H1V" "H1P" "H1I" "H1D" "H2S" "H2V" \
+"H2P" "H2I" "H2D" "PMS" "PSP" "PSI" "PSD" "PS1" "MUP" "MDN" "TMS" "TMR" "TRM" \
+"SOL" "HOM" "CMD" "MLD" "SOD" "EOD" "NOP" 
+
+
+enum keywordIndex {
+_SYN_,_ACK_,_NAK_,_SWV_,_HWV_,_GIT_,_MEM_,_SSN_,_HLP_,_FTL_,_ALT_,_WAR_,_INF_,
+_DBG_,_LOG_,_STC_,_DVL_,_LVL_,_RST_,_BLD_,_STP_,_LCS_,_LCR_,_NOW_,_TIM_,_TS1_,
+_TS2_,_TMP_,_AMT_,_AMH_,_RED_,_HSW_,_H1S_,_H1V_,_H1P_,_H1I_,_H1D_,_H2S_,_H2V_,
+_H2P_,_H2I_,_H2D_,_PMS_,_PSP_,_PSI_,_PSD_,_PS1_,_MUP_,_MDN_,_TMS_,_TMR_,_TRM_,
+_SOL_,_HOM_,_CMD_,_MLD_,_SOD_,_EOD_,_NOP_};
+
+// use enum to determine the size of the keyword arrays.
+#define NKEYWORDS  _NOP_ + 1
+
+#endif