Removes a lot of left over comments, adds lumidrive and redboard turbo to travis.yml

3 files changed, 1 insertions, 66 deletions

diff --git a/.travis.yml b/.travis.yml
index 90ed07506..1f47f7e9a 100755
--- a/.travis.yml
+++ b/.travis.yml
@@ -25,7 +25,7 @@ env:
   - TRAVIS_BOARDS="metro_m0_express metro_m4_express pirkey_m0 trellis_m4_express trinket_m0" TRAVIS_SDK=arm
   - TRAVIS_BOARDS="feather_radiofruit_zigbee gemma_m0 hallowing_m0_express itsybitsy_m0_express itsybitsy_m4_express meowmeow" TRAVIS_SDK=arm
   - TRAVIS_BOARDS="feather_m0_express_crickit feather_m0_rfm69 feather_m0_rfm9x feather_m4_express arduino_zero arduino_mkr1300 arduino_mkrzero" TRAVIS_SDK=arm
-  - TRAVIS_BOARDS="circuitplayground_express_crickit feather_m0_adalogger feather_m0_basic feather_m0_express catwan_usbstick pyportal sparkfun_samd21_mini sparkfun_samd21_dev" TRAVIS_SDK=arm
+  - TRAVIS_BOARDS="circuitplayground_express_crickit feather_m0_adalogger feather_m0_basic feather_m0_express catwan_usbstick pyportal sparkfun_samd21_mini sparkfun_samd21_dev sparkfun_lumidrive sparkfun_redboard_turbo" TRAVIS_SDK=arm
 
 addons:
   artifacts:
diff --git a/ports/atmel-samd/boards/sparkfun_lumidrive/mpconfigboard.h b/ports/atmel-samd/boards/sparkfun_lumidrive/mpconfigboard.h
index 855b00c6f..7c7579f6c 100755
--- a/ports/atmel-samd/boards/sparkfun_lumidrive/mpconfigboard.h
+++ b/ports/atmel-samd/boards/sparkfun_lumidrive/mpconfigboard.h
@@ -11,28 +11,16 @@
 #define SPI_FLASH_SCK_PIN    &PIN_PA09
 #define SPI_FLASH_CS_PIN     &PIN_PA13
 
-// All port(pin) definitions should be deleted unless PA06 -- SERCOM0/PAD[2]
-// Will need to scour the repo to figure out why this was done. 
-// I'm guessing these ports are defined elsewehere by default rather than needing to
-// repeatedly define them. Saves time to name outliers than participants in
-// some cases. 
 #define MICROPY_PORT_A    ( 0 )
 #define MICROPY_PORT_B    ( 0 )
 #define MICROPY_PORT_C    ( 0 )
 
-// If you change this, then make sure to update the linker scripts as well to
-// make sure you don't overwrite code.
 #define CIRCUITPY_INTERNAL_NVM_SIZE 256
 
 #define BOARD_FLASH_SIZE (0x00040000 - 0x2000 - CIRCUITPY_INTERNAL_NVM_SIZE)
 
 #define BOARD_HAS_CRYSTAL 1
 
-
-// The LUMIDrive board exposed pins are limited, and I2C, TX/RX, and SPI are not 
-// really exposed but if they are not define (and included in pins.h), Python 
-// won't start/operate. So define here:
-
 //I2C
 #define DEFAULT_I2C_BUS_SCL (&pin_PA23)
 #define DEFAULT_I2C_BUS_SDA (&pin_PA22)
diff --git a/ports/atmel-samd/boards/sparkfun_redboard_turbo/mpconfigboard.h b/ports/atmel-samd/boards/sparkfun_redboard_turbo/mpconfigboard.h
index 4bd872dd3..cf7c3998b 100755
--- a/ports/atmel-samd/boards/sparkfun_redboard_turbo/mpconfigboard.h
+++ b/ports/atmel-samd/boards/sparkfun_redboard_turbo/mpconfigboard.h
@@ -10,48 +10,11 @@
 // Clock rates are off: Salae reads 12MHz which is the limit even though we set it to the safer 8MHz.
 #define SPI_FLASH_BAUDRATE  (8000000)
 
-//
-// SPI Flash definitions. The flash SPI MOSI, MISO and SCK need to be on the 
-// same SERCOM - check the SAMD21 spec to determien which SERCOM to use 
-// (post PINs have 2 SERCOMS to work with)
-//
 #define SPI_FLASH_MOSI_PIN          &pin_PB22
 #define SPI_FLASH_MISO_PIN          &pin_PB03
 #define SPI_FLASH_SCK_PIN           &pin_PB23
 #define SPI_FLASH_CS_PIN            &pin_PA13
 
-
-// #define SPI_FLASH_MOSI_PIN_FUNCTION PINMUX_PB22D_SERCOM5_PAD2
-// #define SPI_FLASH_MISO_PIN_FUNCTION PINMUX_PB03D_SERCOM5_PAD1
-// #define SPI_FLASH_SCK_PIN_FUNCTION  PINMUX_PB23D_SERCOM5_PAD3
-// #define SPI_FLASH_SERCOM            SERCOM5
-// #define SPI_FLASH_SERCOM_INDEX      5
-// #define SPI_FLASH_MOSI_PAD          2
-// #define SPI_FLASH_MISO_PAD          1
-// #define SPI_FLASH_SCK_PAD           3
-
-
-// // <o> Transmit Data Pinout
-
-// // 
-// // The logic for DOPO and DIPO is the following
-// // In master SPI operation    
-// //    DIPO  <pad #> = MISO
-// //    DOPO  - Based on the below table, where 
-// //           <DOPO> = [MOSI PAD, SCK PAD]
-// //           <0x0>  = PAD[0,1]
-// //           <0x1>  = PAD[2,3]
-// //           <0x2>  = PAD[3,1]
-// //           <0x3>  = PAD[0,3]
-// //
-// /// For the RedBoard Turbo Board DOPO [2,3] => 1
-// #define SPI_FLASH_DOPO              1   
-// #define SPI_FLASH_DIPO              1   // same as MISO pad
-
-// These are pins not to reset. 
-// This map to the pins as defined above for FLASH. Note the PORT letters - assign A-to-A, B-to-B ..etc
-// PA24 and PA25 are for USB
-
 #define MICROPY_PORT_A        ( 0 ) 
 #define MICROPY_PORT_B        ( 0 )
 #define MICROPY_PORT_C        ( 0 )
@@ -63,22 +26,6 @@
 
 #define BOARD_FLASH_SIZE (0x00040000 - 0x2000 - CIRCUITPY_INTERNAL_NVM_SIZE)
 
-
-// What external flash device is being used on this board?
-// The devices are defined in "exteral_flash/devices.h", which 
-// contains a flash struct def and a list of #defines for each
-// supported/defined flash module. 
-//
-// This board - the LUMIDrive - uses a W25Q32FV component. It's 
-// definition was added to devices.h, based on the winbond spec sheet.
-//
-// You can list N number of devices - just update the count define and comma 
-// seperate the EXTERNAL_FLASH_DEVICES list of devices.  
-                               
-// #define EXTERNAL_FLASH_DEVICE_COUNT 1
-// #define EXTERNAL_FLASH_DEVICES W25Q32FV
-
-
 #define BOARD_HAS_CRYSTAL 1