Remove obsolete esp.rst, network.rst

1 files changed, 0 insertions, 85 deletions

diff --git a/docs/library/esp.rst b/docs/library/esp.rst
deleted file mode 100644
index 125aaa890..000000000
--- a/docs/library/esp.rst
+++ /dev/null
@@ -1,85 +0,0 @@
-:mod:`esp` --- functions related to the ESP8266
-===============================================
-
-.. include:: ../templates/unsupported_in_circuitpython.inc
-
-.. module:: esp
-    :synopsis: functions related to the ESP8266
-
-The ``esp`` module contains specific functions related to the ESP8266 module.
-
-
-Functions
----------
-
-.. function:: sleep_type([sleep_type])
-
-    Get or set the sleep type.
-
-    If the *sleep_type* parameter is provided, sets the sleep type to its
-    value. If the function is called without parameters, returns the current
-    sleep type.
-
-    The possible sleep types are defined as constants:
-
-        * ``SLEEP_NONE`` -- all functions enabled,
-        * ``SLEEP_MODEM`` -- modem sleep, shuts down the WiFi Modem circuit.
-        * ``SLEEP_LIGHT`` -- light sleep, shuts down the WiFi Modem circuit
-          and suspends the processor periodically.
-
-    The system enters the set sleep mode automatically when possible.
-
-.. function:: deepsleep(time=0)
-
-    Enter deep sleep.
-
-    The whole module powers down, except for the RTC clock circuit, which can
-    be used to restart the module after the specified time if the pin 16 is
-    connected to the reset pin. Otherwise the module will sleep until manually
-    reset.
-
-.. function:: flash_id()
-
-    Read the device ID of the flash memory.
-
-.. function:: flash_read(byte_offset, length_or_buffer)
-
-.. function:: flash_write(byte_offset, bytes)
-
-.. function:: flash_erase(sector_no)
-
-.. function:: set_native_code_location(start, length)
-
-    Set the location that native code will be placed for execution after it is
-    compiled.  Native code is emitted when the ``@micropython.native``,
-    ``@micropython.viper`` and ``@micropython.asm_xtensa`` decorators are applied
-    to a function.  The ESP8266 must execute code from either iRAM or the lower
-    1MByte of flash (which is memory mapped), and this function controls the
-    location.
-
-    If *start* and *length* are both ``None`` then the native code location is
-    set to the unused portion of memory at the end of the iRAM1 region.  The
-    size of this unused portion depends on the firmware and is typically quite
-    small (around 500 bytes), and is enough to store a few very small
-    functions.  The advantage of using this iRAM1 region is that it does not
-    get worn out by writing to it.
-
-    If neither *start* nor *length* are ``None`` then they should be integers.
-    *start* should specify the byte offset from the beginning of the flash at
-    which native code should be stored.  *length* specifies how many bytes of
-    flash from *start* can be used to store native code.  *start* and *length*
-    should be multiples of the sector size (being 4096 bytes).  The flash will
-    be automatically erased before writing to it so be sure to use a region of
-    flash that is not otherwise used, for example by the firmware or the
-    filesystem.
-
-    When using the flash to store native code *start+length* must be less
-    than or equal to 1MByte.  Note that the flash can be worn out if repeated
-    erasures (and writes) are made so use this feature sparingly.
-    In particular, native code needs to be recompiled and rewritten to flash
-    on each boot (including wake from deepsleep).
-
-    In both cases above, using iRAM1 or flash, if there is no more room left
-    in the specified region then the use of a native decorator on a function
-    will lead to `MemoryError` exception being raised during compilation of
-    that function.