Did board, digitalio, displayio

19 files changed, 610 insertions, 627 deletions

diff --git a/shared-bindings/board/__init__.c b/shared-bindings/board/__init__.c
index 3dda59fb8..501879be8 100644
--- a/shared-bindings/board/__init__.c
+++ b/shared-bindings/board/__init__.c
@@ -29,7 +29,7 @@
 
 #include "shared-bindings/board/__init__.h"
 
-//| :mod:`board` --- Board specific pin names
+//| """:mod:`board` --- Board specific pin names
 //| ========================================================
 //|
 //| .. module:: board
@@ -39,11 +39,11 @@
 //| board so don't expect portability when using this module.
 //|
 //| .. warning:: The board module varies by board. The APIs documented here may or may not be
-//|              available on a specific board.
+//|              available on a specific board."""
 
-//| .. function:: I2C()
-//|
-//|   Returns the `busio.I2C` object for the board designated SDA and SCL pins. It is a singleton.
+//| def I2C() -> Any:
+//|     """Returns the `busio.I2C` object for the board designated SDA and SCL pins. It is a singleton."""
+//|     ...
 //|
 
 #if BOARD_I2C
@@ -65,10 +65,10 @@ mp_obj_t board_i2c(void) {
 MP_DEFINE_CONST_FUN_OBJ_0(board_i2c_obj, board_i2c);
 
 
-//| .. function:: SPI()
-//|
-//|   Returns the `busio.SPI` object for the board designated SCK, MOSI and MISO pins. It is a
-//|   singleton.
+//| def SPI() -> Any:
+//|     """Returns the `busio.SPI` object for the board designated SCK, MOSI and MISO pins. It is a
+//|     singleton."""
+//|     ...
 //|
 #if BOARD_SPI
 mp_obj_t board_spi(void) {
@@ -89,15 +89,14 @@ mp_obj_t board_spi(void) {
 #endif
 MP_DEFINE_CONST_FUN_OBJ_0(board_spi_obj, board_spi);
 
-//| .. function:: UART()
-//|
-//|   Returns the `busio.UART` object for the board designated TX and RX pins. It is a singleton.
-//|
-//|   The object created uses the default parameter values for `busio.UART`. If you need to set
-//|   parameters that are not changeable after creation, such as ``receiver_buffer_size``,
-//|   do not use `board.UART()`; instead create a `busio.UART` object explicitly with the
-//|   desired parameters.
+//| def UART() -> Any:
+//|     """Returns the `busio.UART` object for the board designated TX and RX pins. It is a singleton.
 //|
+//|     The object created uses the default parameter values for `busio.UART`. If you need to set
+//|     parameters that are not changeable after creation, such as ``receiver_buffer_size``,
+//|     do not use `board.UART()`; instead create a `busio.UART` object explicitly with the
+//|     desired parameters."""
+//|     ...
 //|
 #if BOARD_UART
 mp_obj_t board_uart(void) {
diff --git a/shared-bindings/digitalio/DigitalInOut.c b/shared-bindings/digitalio/DigitalInOut.c
index 39da00cf7..5fffb3f65 100644
--- a/shared-bindings/digitalio/DigitalInOut.c
+++ b/shared-bindings/digitalio/DigitalInOut.c
@@ -43,23 +43,23 @@
 #include "shared-bindings/util.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: digitalio
+//| class DigitalInOut:
+//|     """.. currentmodule:: digitalio
 //|
-//| :class:`DigitalInOut` -- digital input and output
-//| =========================================================
+//|     :class:`DigitalInOut` -- digital input and output
+//|     =========================================================
 //|
-//| A DigitalInOut is used to digitally control I/O pins. For analog control of
-//| a pin, see the :py:class:`analogio.AnalogIn` and
-//| :py:class:`analogio.AnalogOut` classes.
+//|     A DigitalInOut is used to digitally control I/O pins. For analog control of
+//|     a pin, see the :py:class:`analogio.AnalogIn` and
+//|     :py:class:`analogio.AnalogOut` classes."""
 //|
-
-//| .. class:: DigitalInOut(pin)
-//|
-//|   Create a new DigitalInOut object associated with the pin. Defaults to input
-//|   with no pull. Use :py:meth:`switch_to_input` and
-//|   :py:meth:`switch_to_output` to change the direction.
+//|     def __init__(self, pin: microcontroller.Pin):
+//|         """Create a new DigitalInOut object associated with the pin. Defaults to input
+//|         with no pull. Use :py:meth:`switch_to_input` and
+//|         :py:meth:`switch_to_output` to change the direction.
 //|
-//|   :param ~microcontroller.Pin pin: The pin to control
+//|         :param ~microcontroller.Pin pin: The pin to control"""
+//|         ...
 //|
 STATIC mp_obj_t digitalio_digitalinout_make_new(const mp_obj_type_t *type,
         mp_uint_t n_args, const mp_obj_t *args, mp_map_t *kw_args) {
@@ -74,9 +74,9 @@ STATIC mp_obj_t digitalio_digitalinout_make_new(const mp_obj_type_t *type,
     return MP_OBJ_FROM_PTR(self);
 }
 
-//|   .. method:: deinit()
-//|
-//|      Turn off the DigitalInOut and release the pin for other use.
+//|     def deinit(self, ) -> Any:
+//|         """Turn off the DigitalInOut and release the pin for other use."""
+//|         ...
 //|
 STATIC mp_obj_t digitalio_digitalinout_obj_deinit(mp_obj_t self_in) {
     digitalio_digitalinout_obj_t *self = MP_OBJ_TO_PTR(self_in);
@@ -85,16 +85,16 @@ STATIC mp_obj_t digitalio_digitalinout_obj_deinit(mp_obj_t self_in) {
 }
 MP_DEFINE_CONST_FUN_OBJ_1(digitalio_digitalinout_deinit_obj, digitalio_digitalinout_obj_deinit);
 
-//|   .. method:: __enter__()
-//|
-//|      No-op used by Context Managers.
+//|     def __enter__(self, ) -> Any:
+//|         """No-op used by Context Managers."""
+//|         ...
 //|
 //  Provided by context manager helper.
 
-//|   .. method:: __exit__()
-//|
-//|      Automatically deinitializes the hardware when exiting a context. See
-//|      :ref:`lifetime-and-contextmanagers` for more info.
+//|     def __exit__(self, ) -> Any:
+//|         """Automatically deinitializes the hardware when exiting a context. See
+//|         :ref:`lifetime-and-contextmanagers` for more info."""
+//|         ...
 //|
 STATIC mp_obj_t digitalio_digitalinout_obj___exit__(size_t n_args, const mp_obj_t *args) {
     (void)n_args;
@@ -109,14 +109,13 @@ STATIC void check_for_deinit(digitalio_digitalinout_obj_t *self) {
     }
 }
 
+//|     def switch_to_output(self, value: bool = False, drive_mode: digitalio.DriveMode = digitalio.DriveMode.PUSH_PULL) -> Any:
+//|           """Set the drive mode and value and then switch to writing out digital
+//|           values.
 //|
-//|   .. method:: switch_to_output(value=False, drive_mode=digitalio.DriveMode.PUSH_PULL)
-//|
-//|       Set the drive mode and value and then switch to writing out digital
-//|       values.
-//|
-//|       :param bool value: default value to set upon switching
-//|       :param ~digitalio.DriveMode drive_mode: drive mode for the output
+//|           :param bool value: default value to set upon switching
+//|           :param ~digitalio.DriveMode drive_mode: drive mode for the output"""
+//|           ...
 //|
 STATIC mp_obj_t digitalio_digitalinout_switch_to_output(size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_value, ARG_drive_mode };
@@ -139,22 +138,22 @@ STATIC mp_obj_t digitalio_digitalinout_switch_to_output(size_t n_args, const mp_
 }
 MP_DEFINE_CONST_FUN_OBJ_KW(digitalio_digitalinout_switch_to_output_obj, 1, digitalio_digitalinout_switch_to_output);
 
-//|   .. method:: switch_to_input(pull=None)
-//|
-//|     Set the pull and then switch to read in digital values.
+//|     def switch_to_input(self, pull: Pull = None) -> Any:
+//|         """Set the pull and then switch to read in digital values.
 //|
-//|     :param Pull pull: pull configuration for the input
+//|         :param Pull pull: pull configuration for the input
 //|
-//|     Example usage::
+//|         Example usage::
 //|
-//|       import digitalio
-//|       import board
+//|           import digitalio
+//|           import board
 //|
-//|       switch = digitalio.DigitalInOut(board.SLIDE_SWITCH)
-//|       switch.switch_to_input(pull=digitalio.Pull.UP)
-//|       # Or, after switch_to_input
-//|       switch.pull = digitalio.Pull.UP
-//|       print(switch.value)
+//|           switch = digitalio.DigitalInOut(board.SLIDE_SWITCH)
+//|           switch.switch_to_input(pull=digitalio.Pull.UP)
+//|           # Or, after switch_to_input
+//|           switch.pull = digitalio.Pull.UP
+//|           print(switch.value)"""
+//|         ...
 //|
 STATIC mp_obj_t digitalio_digitalinout_switch_to_input(size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_pull };
@@ -178,14 +177,13 @@ STATIC mp_obj_t digitalio_digitalinout_switch_to_input(size_t n_args, const mp_o
 }
 MP_DEFINE_CONST_FUN_OBJ_KW(digitalio_digitalinout_switch_to_input_obj, 1, digitalio_digitalinout_switch_to_input);
 
-//|   .. attribute:: direction
-//|
-//|     The direction of the pin.
+//|     direction: Any = ...
+//|     """The direction of the pin.
 //|
 //|     Setting this will use the defaults from the corresponding
 //|     :py:meth:`switch_to_input` or :py:meth:`switch_to_output` method. If
 //|     you want to set pull, value or drive mode prior to switching, then use
-//|     those methods instead.
+//|     those methods instead."""
 //|
 typedef struct {
     mp_obj_base_t base;
@@ -225,9 +223,8 @@ const mp_obj_property_t digitalio_digitalio_direction_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: value
-//|
-//|     The digital logic level of the pin.
+//|     value: Any = ...
+//|     """The digital logic level of the pin."""
 //|
 STATIC mp_obj_t digitalio_digitalinout_obj_get_value(mp_obj_t self_in) {
     digitalio_digitalinout_obj_t *self = MP_OBJ_TO_PTR(self_in);
@@ -256,12 +253,11 @@ const mp_obj_property_t digitalio_digitalinout_value_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: drive_mode
-//|
-//|     The pin drive mode. One of:
+//|     drive_mode: Any = ...
+//|     """The pin drive mode. One of:
 //|
 //|     - `digitalio.DriveMode.PUSH_PULL`
-//|     - `digitalio.DriveMode.OPEN_DRAIN`
+//|     - `digitalio.DriveMode.OPEN_DRAIN`"""
 //|
 STATIC mp_obj_t digitalio_digitalinout_obj_get_drive_mode(mp_obj_t self_in) {
     digitalio_digitalinout_obj_t *self = MP_OBJ_TO_PTR(self_in);
@@ -301,15 +297,14 @@ const mp_obj_property_t digitalio_digitalio_drive_mode_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: pull
-//|
-//|     The pin pull direction. One of:
+//|     pull: Any = ...
+//|     """The pin pull direction. One of:
 //|
 //|     - `digitalio.Pull.UP`
 //|     - `digitalio.Pull.DOWN`
 //|     - `None`
 //|
-//|     :raises AttributeError: if `direction` is :py:data:`~digitalio.Direction.OUTPUT`.
+//|     :raises AttributeError: if `direction` is :py:data:`~digitalio.Direction.OUTPUT`."""
 //|
 STATIC mp_obj_t digitalio_digitalinout_obj_get_pull(mp_obj_t self_in) {
     digitalio_digitalinout_obj_t *self = MP_OBJ_TO_PTR(self_in);
diff --git a/shared-bindings/digitalio/Direction.c b/shared-bindings/digitalio/Direction.c
index c8188fc89..0586e95de 100644
--- a/shared-bindings/digitalio/Direction.c
+++ b/shared-bindings/digitalio/Direction.c
@@ -38,23 +38,22 @@
 #include "shared-bindings/microcontroller/Pin.h"
 #include "shared-bindings/digitalio/DigitalInOut.h"
 
-//| .. currentmodule:: digitalio
+//| class Direction:
+//|     """.. currentmodule:: digitalio
 //|
-//| :class:`Direction` -- defines the direction of a digital pin
-//| =============================================================
+//|     :class:`Direction` -- defines the direction of a digital pin
+//|     ============================================================="""
 //|
-//| .. class:: Direction
+//|     def __init__(self, ):
+//|         """Enum-like class to define which direction the digital values are
+//|         going."""
+//|         ...
 //|
-//|     Enum-like class to define which direction the digital values are
-//|     going.
+//|     INPUT: Any = ...
+//|     """Read digital data in"""
 //|
-//|     .. data:: INPUT
-//|
-//|       Read digital data in
-//|
-//|     .. data:: OUTPUT
-//|
-//|       Write digital data out
+//|     OUTPUT: Any = ...
+//|     """Write digital data out"""
 //|
 const mp_obj_type_t digitalio_direction_type;
 
diff --git a/shared-bindings/digitalio/DriveMode.c b/shared-bindings/digitalio/DriveMode.c
index 51e1e2ee5..23745b046 100644
--- a/shared-bindings/digitalio/DriveMode.c
+++ b/shared-bindings/digitalio/DriveMode.c
@@ -26,24 +26,23 @@
 
 #include "shared-bindings/digitalio/DriveMode.h"
 
-//| .. currentmodule:: digitalio
+//| class DriveMode:
+//|     """.. currentmodule:: digitalio
 //|
-//| :class:`DriveMode` -- defines the drive mode of a digital pin
-//| =============================================================
+//|     :class:`DriveMode` -- defines the drive mode of a digital pin
+//|     ============================================================="""
 //|
-//| .. class:: DriveMode
+//|     def __init__(self, ):
+//|         """Enum-like class to define the drive mode used when outputting
+//|         digital values."""
+//|         ...
 //|
-//|     Enum-like class to define the drive mode used when outputting
-//|     digital values.
+//|     PUSH_PULL: Any = ...
+//|     """Output both high and low digital values"""
 //|
-//|     .. data:: PUSH_PULL
-//|
-//|       Output both high and low digital values
-//|
-//|     .. data:: OPEN_DRAIN
-//|
-//|       Output low digital values but go into high z for digital high. This is
-//|       useful for i2c and other protocols that share a digital line.
+//|     OPEN_DRAIN: Any = ...
+//|     """Output low digital values but go into high z for digital high. This is
+//|     useful for i2c and other protocols that share a digital line."""
 //|
 const mp_obj_type_t digitalio_drive_mode_type;
 
diff --git a/shared-bindings/digitalio/Pull.c b/shared-bindings/digitalio/Pull.c
index 813268db7..1e64d0788 100644
--- a/shared-bindings/digitalio/Pull.c
+++ b/shared-bindings/digitalio/Pull.c
@@ -26,25 +26,24 @@
 
 #include "shared-bindings/digitalio/Pull.h"
 
-//| .. currentmodule:: digitalio
+//| class Pull:
+//|     """.. currentmodule:: digitalio
 //|
-//| :class:`Pull` -- defines the pull of a digital input pin
-//| =============================================================
+//|     :class:`Pull` -- defines the pull of a digital input pin
+//|     ============================================================="""
 //|
-//| .. class:: Pull
+//|     def __init__(self, ):
+//|         """Enum-like class to define the pull value, if any, used while reading
+//|         digital values in."""
+//|         ...
 //|
-//|     Enum-like class to define the pull value, if any, used while reading
-//|     digital values in.
+//|     UP: Any = ...
+//|     """When the input line isn't being driven the pull up can pull the state
+//|     of the line high so it reads as true."""
 //|
-//|     .. data:: UP
-//|
-//|       When the input line isn't being driven the pull up can pull the state
-//|       of the line high so it reads as true.
-//|
-//|     .. data:: DOWN
-//|
-//|       When the input line isn't being driven the pull down can pull the
-//|       state of the line low so it reads as false.
+//|     DOWN: Any = ...
+//|     """When the input line isn't being driven the pull down can pull the
+//|     state of the line low so it reads as false."""
 //|
 const mp_obj_type_t digitalio_pull_type;
 
diff --git a/shared-bindings/digitalio/__init__.c b/shared-bindings/digitalio/__init__.c
index 1632262d2..5a11436a2 100644
--- a/shared-bindings/digitalio/__init__.c
+++ b/shared-bindings/digitalio/__init__.c
@@ -38,7 +38,7 @@
 
 #include "py/runtime.h"
 
-//| :mod:`digitalio` --- Basic digital pin support
+//| """:mod:`digitalio` --- Basic digital pin support
 //| =================================================
 //|
 //| .. module:: digitalio
@@ -86,7 +86,7 @@
 //|       led.value = True
 //|       time.sleep(0.1)
 //|       led.value = False
-//|       time.sleep(0.1)
+//|       time.sleep(0.1)"""
 //|
 
 STATIC const mp_rom_map_elem_t digitalio_module_globals_table[] = {
diff --git a/shared-bindings/displayio/Bitmap.c b/shared-bindings/displayio/Bitmap.c
index 391f3e595..d15c3b107 100644
--- a/shared-bindings/displayio/Bitmap.c
+++ b/shared-bindings/displayio/Bitmap.c
@@ -36,22 +36,23 @@
 #include "shared-bindings/util.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: displayio
+//| class Bitmap:
+//|     """.. currentmodule:: displayio
 //|
-//| :class:`Bitmap` -- Stores values in a 2D array
-//| ==========================================================================
+//|     :class:`Bitmap` -- Stores values in a 2D array
+//|     ==========================================================================
 //|
-//| Stores values of a certain size in a 2D array
+//|     Stores values of a certain size in a 2D array"""
 //|
-//| .. class:: Bitmap(width, height, value_count)
+//|     def __init__(self, width: int, height: int, value_count: int):
+//|         """Create a Bitmap object with the given fixed size. Each pixel stores a value that is used to
+//|         index into a corresponding palette. This enables differently colored sprites to share the
+//|         underlying Bitmap. value_count is used to minimize the memory used to store the Bitmap.
 //|
-//|   Create a Bitmap object with the given fixed size. Each pixel stores a value that is used to
-//|   index into a corresponding palette. This enables differently colored sprites to share the
-//|   underlying Bitmap. value_count is used to minimize the memory used to store the Bitmap.
-//|
-//|   :param int width: The number of values wide
-//|   :param int height: The number of values high
-//|   :param int value_count: The number of possible pixel values.
+//|         :param int width: The number of values wide
+//|         :param int height: The number of values high
+//|         :param int value_count: The number of possible pixel values."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_bitmap_make_new(const mp_obj_type_t *type, size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     mp_arg_check_num(n_args, kw_args, 3, 3, false);
@@ -77,9 +78,8 @@ STATIC mp_obj_t displayio_bitmap_make_new(const mp_obj_type_t *type, size_t n_ar
 
     return MP_OBJ_FROM_PTR(self);
 }
-//|   .. attribute:: width
-//|
-//|      Width of the bitmap. (read only)
+//|     width: Any = ...
+//|     """Width of the bitmap. (read only)"""
 //|
 STATIC mp_obj_t displayio_bitmap_obj_get_width(mp_obj_t self_in) {
     displayio_bitmap_t *self = MP_OBJ_TO_PTR(self_in);
@@ -96,9 +96,8 @@ const mp_obj_property_t displayio_bitmap_width_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: height
-//|
-//|      Height of the bitmap. (read only)
+//|     height: Any = ...
+//|     """Height of the bitmap. (read only)"""
 //|
 STATIC mp_obj_t displayio_bitmap_obj_get_height(mp_obj_t self_in) {
     displayio_bitmap_t *self = MP_OBJ_TO_PTR(self_in);
@@ -115,23 +114,23 @@ const mp_obj_property_t displayio_bitmap_height_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. method:: __getitem__(index)
+//|     def __getitem__(self, index: Any) -> Any:
+//|         """Returns the value at the given index. The index can either be an x,y tuple or an int equal
+//|         to ``y * width + x``.
 //|
-//|     Returns the value at the given index. The index can either be an x,y tuple or an int equal
-//|     to ``y * width + x``.
+//|         This allows you to::
 //|
-//|     This allows you to::
+//|           print(bitmap[0,1])"""
+//|         ...
 //|
-//|       print(bitmap[0,1])
+//|     def __setitem__(self, index: Any, value: Any) -> Any:
+//|         """Sets the value at the given index. The index can either be an x,y tuple or an int equal
+//|         to ``y * width + x``.
 //|
-//|   .. method:: __setitem__(index, value)
+//|         This allows you to::
 //|
-//|     Sets the value at the given index. The index can either be an x,y tuple or an int equal
-//|     to ``y * width + x``.
-//|
-//|     This allows you to::
-//|
-//|       bitmap[0,1] = 3
+//|           bitmap[0,1] = 3"""
+//|         ...
 //|
 STATIC mp_obj_t bitmap_subscr(mp_obj_t self_in, mp_obj_t index_obj, mp_obj_t value_obj) {
     if (value_obj == mp_const_none) {
@@ -178,9 +177,9 @@ STATIC mp_obj_t bitmap_subscr(mp_obj_t self_in, mp_obj_t index_obj, mp_obj_t val
     return mp_const_none;
 }
 
-//|   .. method:: fill(value)
-//|
-//|      Fills the bitmap with the supplied palette index value.
+//|     def fill(self, value: Any) -> Any:
+//|         """Fills the bitmap with the supplied palette index value."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_bitmap_obj_fill(mp_obj_t self_in, mp_obj_t value_obj) {
     displayio_bitmap_t *self = MP_OBJ_TO_PTR(self_in);
diff --git a/shared-bindings/displayio/ColorConverter.c b/shared-bindings/displayio/ColorConverter.c
index db2d1b6e2..1d6e5a0cc 100644
--- a/shared-bindings/displayio/ColorConverter.c
+++ b/shared-bindings/displayio/ColorConverter.c
@@ -36,18 +36,20 @@
 #include "shared-bindings/util.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: displayio
+//| class ColorConverter:
+//|     """.. currentmodule:: displayio
 //|
-//| :class:`ColorConverter` -- Converts one color format to another
-//| =========================================================================================
+//|     :class:`ColorConverter` -- Converts one color format to another
+//|     =========================================================================================
 //|
-//| Converts one color format to another.
+//|     Converts one color format to another."""
 //|
-//| .. class:: ColorConverter(*, dither=False)
+//|     def __init__(self, *, dither: bool = False):
+//|         """Create a ColorConverter object to convert color formats. Only supports RGB888 to RGB565
+//|         currently.
+//|         :param bool dither: Adds random noise to dither the output image"""
+//|         ...
 //|
-//|   Create a ColorConverter object to convert color formats. Only supports RGB888 to RGB565
-//|   currently.
-//|   :param bool dither: Adds random noise to dither the output image
 
 // TODO(tannewt): Add support for other color formats.
 //|
@@ -68,9 +70,9 @@ STATIC mp_obj_t displayio_colorconverter_make_new(const mp_obj_type_t *type, siz
     return MP_OBJ_FROM_PTR(self);
 }
 
-//|   .. method:: convert(color)
-//|
-//|   Converts the given RGB888 color to RGB565
+//|     def convert(self, color: Any) -> Any:
+//|         """Converts the given RGB888 color to RGB565"""
+//|         ...
 //|
 STATIC mp_obj_t displayio_colorconverter_obj_convert(mp_obj_t self_in, mp_obj_t color_obj) {
     displayio_colorconverter_t *self = MP_OBJ_TO_PTR(self_in);
@@ -87,10 +89,9 @@ STATIC mp_obj_t displayio_colorconverter_obj_convert(mp_obj_t self_in, mp_obj_t
 }
 MP_DEFINE_CONST_FUN_OBJ_2(displayio_colorconverter_convert_obj, displayio_colorconverter_obj_convert);
 
-//|   .. attribute:: dither
-//|
-//|     When true the color converter dithers the output by adding random noise when
-//|     truncating to display bitdepth
+//|     dither: Any = ...
+//|     """When true the color converter dithers the output by adding random noise when
+//|     truncating to display bitdepth"""
 //|
 STATIC mp_obj_t displayio_colorconverter_obj_get_dither(mp_obj_t self_in) {
     displayio_colorconverter_t *self = MP_OBJ_TO_PTR(self_in);
diff --git a/shared-bindings/displayio/Display.c b/shared-bindings/displayio/Display.c
index a22b2add2..12abec1c8 100644
--- a/shared-bindings/displayio/Display.c
+++ b/shared-bindings/displayio/Display.c
@@ -39,73 +39,74 @@
 #include "shared-module/displayio/__init__.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: displayio
-//|
-//| :class:`Display` -- Manage updating a display over a display bus
-//| ==========================================================================
-//|
-//| This initializes a display and connects it into CircuitPython. Unlike other
-//| objects in CircuitPython, Display objects live until `displayio.release_displays()`
-//| is called. This is done so that CircuitPython can use the display itself.
-//|
-//| Most people should not use this class directly. Use a specific display driver instead that will
-//| contain the initialization sequence at minimum.
-//|
-//| .. class:: Display(display_bus, init_sequence, *, width, height, colstart=0, rowstart=0, rotation=0, color_depth=16, grayscale=False, pixels_in_byte_share_row=True, bytes_per_cell=1, reverse_pixels_in_byte=False, set_column_command=0x2a, set_row_command=0x2b, write_ram_command=0x2c, set_vertical_scroll=0, backlight_pin=None, brightness_command=None, brightness=1.0, auto_brightness=False, single_byte_bounds=False, data_as_commands=False, auto_refresh=True, native_frames_per_second=60)
-//|
-//|   Create a Display object on the given display bus (`displayio.FourWire` or `displayio.ParallelBus`).
-//|
-//|   The ``init_sequence`` is bitpacked to minimize the ram impact. Every command begins with a
-//|   command byte followed by a byte to determine the parameter count and if a delay is need after.
-//|   When the top bit of the second byte is 1, the next byte will be the delay time in milliseconds.
-//|   The remaining 7 bits are the parameter count excluding any delay byte. The third through final
-//|   bytes are the remaining command parameters. The next byte will begin a new command definition.
-//|   Here is a portion of ILI9341 init code:
-//|
-//|   .. code-block:: python
-//|
-//|     init_sequence = (b"\xe1\x0f\x00\x0E\x14\x03\x11\x07\x31\xC1\x48\x08\x0F\x0C\x31\x36\x0F" # Set Gamma
-//|                      b"\x11\x80\x78"# Exit Sleep then delay 0x78 (120ms)
-//|                      b"\x29\x80\x78"# Display on then delay 0x78 (120ms)
-//|                     )
-//|      display = displayio.Display(display_bus, init_sequence, width=320, height=240)
-//|
-//|   The first command is 0xe1 with 15 (0xf) parameters following. The second and third are 0x11 and
-//|   0x29 respectively with delays (0x80) of 120ms (0x78) and no parameters. Multiple byte literals
-//|   (b"") are merged together on load. The parens are needed to allow byte literals on subsequent
-//|   lines.
-//|
-//|   The initialization sequence should always leave the display memory access inline with the scan
-//|   of the display to minimize tearing artifacts.
-//|
-//|   :param display_bus: The bus that the display is connected to
-//|   :type display_bus: displayio.FourWire or displayio.ParallelBus
-//|   :param buffer init_sequence: Byte-packed initialization sequence.
-//|   :param int width: Width in pixels
-//|   :param int height: Height in pixels
-//|   :param int colstart: The index if the first visible column
-//|   :param int rowstart: The index if the first visible row
-//|   :param int rotation: The rotation of the display in degrees clockwise. Must be in 90 degree increments (0, 90, 180, 270)
-//|   :param int color_depth: The number of bits of color per pixel transmitted. (Some displays
-//|       support 18 bit but 16 is easier to transmit. The last bit is extrapolated.)
-//|   :param bool grayscale: True if the display only shows a single color.
-//|   :param bool pixels_in_byte_share_row: True when pixels are less than a byte and a byte includes pixels from the same row of the display. When False, pixels share a column.
-//|   :param int bytes_per_cell: Number of bytes per addressable memory location when color_depth < 8. When greater than one, bytes share a row or column according to pixels_in_byte_share_row.
-//|   :param bool reverse_pixels_in_byte: Reverses the pixel order within each byte when color_depth < 8. Does not apply across multiple bytes even if there is more than one byte per cell (bytes_per_cell.)
-//|   :param bool reverse_bytes_in_word: Reverses the order of bytes within a word when color_depth == 16
-//|   :param int set_column_command: Command used to set the start and end columns to update
-//|   :param int set_row_command: Command used so set the start and end rows to update
-//|   :param int write_ram_command: Command used to write pixels values into the update region. Ignored if data_as_commands is set.
-//|   :param int set_vertical_scroll: Command used to set the first row to show
-//|   :param microcontroller.Pin backlight_pin: Pin connected to the display's backlight
-//|   :param int brightness_command: Command to set display brightness. Usually available in OLED controllers.
-//|   :param bool brightness: Initial display brightness. This value is ignored if auto_brightness is True.
-//|   :param bool auto_brightness: If True, brightness is controlled via an ambient light sensor or other mechanism.
-//|   :param bool single_byte_bounds: Display column and row commands use single bytes
-//|   :param bool data_as_commands: Treat all init and boundary data as SPI commands. Certain displays require this.
-//|   :param bool auto_refresh: Automatically refresh the screen
-//|   :param int native_frames_per_second: Number of display refreshes per second that occur with the given init_sequence.
-//|   :param bool backlight_on_high: If True, pulling the backlight pin high turns the backlight on.
+//| class Display:
+//|     """.. currentmodule:: displayio
+//|
+//|     :class:`Display` -- Manage updating a display over a display bus
+//|     ==========================================================================
+//|
+//|     This initializes a display and connects it into CircuitPython. Unlike other
+//|     objects in CircuitPython, Display objects live until `displayio.release_displays()`
+//|     is called. This is done so that CircuitPython can use the display itself.
+//|
+//|     Most people should not use this class directly. Use a specific display driver instead that will
+//|     contain the initialization sequence at minimum."""
+//|
+//|     def __init__(self, display_bus: Any, init_sequence: buffer, *, width: int, height: int, colstart: int = 0, rowstart: int = 0, rotation: int = 0, color_depth: int = 16, grayscale: bool = False, pixels_in_byte_share_row: bool = True, bytes_per_cell: int = 1, reverse_pixels_in_byte: bool = False, set_column_command: int = 0x2a, set_row_command: int = 0x2b, write_ram_command: int = 0x2c, set_vertical_scroll: int = 0, backlight_pin: microcontroller.Pin = None, brightness_command: int = None, brightness: bool = 1.0, auto_brightness: bool = False, single_byte_bounds: bool = False, data_as_commands: bool = False, auto_refresh: bool = True, native_frames_per_second: int = 60):
+//|         """Create a Display object on the given display bus (`displayio.FourWire` or `displayio.ParallelBus`).
+//|
+//|         The ``init_sequence`` is bitpacked to minimize the ram impact. Every command begins with a
+//|         command byte followed by a byte to determine the parameter count and if a delay is need after.
+//|         When the top bit of the second byte is 1, the next byte will be the delay time in milliseconds.
+//|         The remaining 7 bits are the parameter count excluding any delay byte. The third through final
+//|         bytes are the remaining command parameters. The next byte will begin a new command definition.
+//|         Here is a portion of ILI9341 init code:
+//|
+//|         .. code-block:: python
+//|
+//|           init_sequence = (b"\xe1\x0f\x00\x0E\x14\x03\x11\x07\x31\xC1\x48\x08\x0F\x0C\x31\x36\x0F" # Set Gamma
+//|                            b"\x11\x80\x78"# Exit Sleep then delay 0x78 (120ms)
+//|                            b"\x29\x80\x78"# Display on then delay 0x78 (120ms)
+//|                           )
+//|            display = displayio.Display(display_bus, init_sequence, width=320, height=240)
+//|
+//|         The first command is 0xe1 with 15 (0xf) parameters following. The second and third are 0x11 and
+//|         0x29 respectively with delays (0x80) of 120ms (0x78) and no parameters. Multiple byte literals
+//|         (b"") are merged together on load. The parens are needed to allow byte literals on subsequent
+//|         lines.
+//|
+//|         The initialization sequence should always leave the display memory access inline with the scan
+//|         of the display to minimize tearing artifacts.
+//|
+//|         :param display_bus: The bus that the display is connected to
+//|         :type display_bus: displayio.FourWire or displayio.ParallelBus
+//|         :param buffer init_sequence: Byte-packed initialization sequence.
+//|         :param int width: Width in pixels
+//|         :param int height: Height in pixels
+//|         :param int colstart: The index if the first visible column
+//|         :param int rowstart: The index if the first visible row
+//|         :param int rotation: The rotation of the display in degrees clockwise. Must be in 90 degree increments (0, 90, 180, 270)
+//|         :param int color_depth: The number of bits of color per pixel transmitted. (Some displays
+//|             support 18 bit but 16 is easier to transmit. The last bit is extrapolated.)
+//|         :param bool grayscale: True if the display only shows a single color.
+//|         :param bool pixels_in_byte_share_row: True when pixels are less than a byte and a byte includes pixels from the same row of the display. When False, pixels share a column.
+//|         :param int bytes_per_cell: Number of bytes per addressable memory location when color_depth < 8. When greater than one, bytes share a row or column according to pixels_in_byte_share_row.
+//|         :param bool reverse_pixels_in_byte: Reverses the pixel order within each byte when color_depth < 8. Does not apply across multiple bytes even if there is more than one byte per cell (bytes_per_cell.)
+//|         :param bool reverse_bytes_in_word: Reverses the order of bytes within a word when color_depth == 16
+//|         :param int set_column_command: Command used to set the start and end columns to update
+//|         :param int set_row_command: Command used so set the start and end rows to update
+//|         :param int write_ram_command: Command used to write pixels values into the update region. Ignored if data_as_commands is set.
+//|         :param int set_vertical_scroll: Command used to set the first row to show
+//|         :param microcontroller.Pin backlight_pin: Pin connected to the display's backlight
+//|         :param int brightness_command: Command to set display brightness. Usually available in OLED controllers.
+//|         :param bool brightness: Initial display brightness. This value is ignored if auto_brightness is True.
+//|         :param bool auto_brightness: If True, brightness is controlled via an ambient light sensor or other mechanism.
+//|         :param bool single_byte_bounds: Display column and row commands use single bytes
+//|         :param bool data_as_commands: Treat all init and boundary data as SPI commands. Certain displays require this.
+//|         :param bool auto_refresh: Automatically refresh the screen
+//|         :param int native_frames_per_second: Number of display refreshes per second that occur with the given init_sequence.
+//|         :param bool backlight_on_high: If True, pulling the backlight pin high turns the backlight on."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_display_make_new(const mp_obj_type_t *type, size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_display_bus, ARG_init_sequence, ARG_width, ARG_height, ARG_colstart, ARG_rowstart, ARG_rotation, ARG_color_depth, ARG_grayscale, ARG_pixels_in_byte_share_row, ARG_bytes_per_cell, ARG_reverse_pixels_in_byte, ARG_reverse_bytes_in_word, ARG_set_column_command, ARG_set_row_command, ARG_write_ram_command, ARG_set_vertical_scroll, ARG_backlight_pin, ARG_brightness_command, ARG_brightness, ARG_auto_brightness, ARG_single_byte_bounds, ARG_data_as_commands, ARG_auto_refresh, ARG_native_frames_per_second, ARG_backlight_on_high };
@@ -190,12 +191,13 @@ static displayio_display_obj_t* native_display(mp_obj_t display_obj) {
     return MP_OBJ_TO_PTR(native_display);
 }
 
-//|   .. method:: show(group)
+//|     def show(self, group: Group) -> Any:
+//|         """Switches to displaying the given group of layers. When group is None, the default
+//|         CircuitPython terminal will be shown.
 //|
-//|     Switches to displaying the given group of layers. When group is None, the default
-//|     CircuitPython terminal will be shown.
+//|         :param Group group: The group to show."""
+//|         ...
 //|
-//|     :param Group group: The group to show.
 STATIC mp_obj_t displayio_display_obj_show(mp_obj_t self_in, mp_obj_t group_in) {
     displayio_display_obj_t *self = native_display(self_in);
     displayio_group_t* group = NULL;
@@ -211,21 +213,21 @@ STATIC mp_obj_t displayio_display_obj_show(mp_obj_t self_in, mp_obj_t group_in)
 }
 MP_DEFINE_CONST_FUN_OBJ_2(displayio_display_show_obj, displayio_display_obj_show);
 
-//|   .. method:: refresh(*, target_frames_per_second=60, minimum_frames_per_second=1)
-//|
-//|     When auto refresh is off, waits for the target frame rate and then refreshes the display,
-//|     returning True. If the call has taken too long since the last refresh call for the given
-//|     target frame rate, then the refresh returns False immediately without updating the screen to
-//|     hopefully help getting caught up.
+//|     def refresh(self, *, target_frames_per_second: int = 60, minimum_frames_per_second: int = 1) -> Any:
+//|         """When auto refresh is off, waits for the target frame rate and then refreshes the display,
+//|         returning True. If the call has taken too long since the last refresh call for the given
+//|         target frame rate, then the refresh returns False immediately without updating the screen to
+//|         hopefully help getting caught up.
 //|
-//|     If the time since the last successful refresh is below the minimum frame rate, then an
-//|     exception will be raised. Set minimum_frames_per_second to 0 to disable.
+//|         If the time since the last successful refresh is below the minimum frame rate, then an
+//|         exception will be raised. Set minimum_frames_per_second to 0 to disable.
 //|
-//|     When auto refresh is on, updates the display immediately. (The display will also update
-//|     without calls to this.)
+//|         When auto refresh is on, updates the display immediately. (The display will also update
+//|         without calls to this.)
 //|
-//|   :param int target_frames_per_second: How many times a second `refresh` should be called and the screen updated.
-//|   :param int minimum_frames_per_second: The minimum number of times the screen should be updated per second.
+//|         :param int target_frames_per_second: How many times a second `refresh` should be called and the screen updated.
+//|         :param int minimum_frames_per_second: The minimum number of times the screen should be updated per second."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_display_obj_refresh(size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_target_frames_per_second, ARG_minimum_frames_per_second };
@@ -246,9 +248,8 @@ STATIC mp_obj_t displayio_display_obj_refresh(size_t n_args, const mp_obj_t *pos
 }
 MP_DEFINE_CONST_FUN_OBJ_KW(displayio_display_refresh_obj, 1, displayio_display_obj_refresh);
 
-//|   .. attribute:: auto_refresh
-//|
-//|     True when the display is refreshed automatically.
+//|     auto_refresh: Any = ...
+//|     """True when the display is refreshed automatically."""
 //|
 STATIC mp_obj_t displayio_display_obj_get_auto_refresh(mp_obj_t self_in) {
     displayio_display_obj_t *self = native_display(self_in);
@@ -272,11 +273,10 @@ const mp_obj_property_t displayio_display_auto_refresh_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: brightness
-//|
-//|     The brightness of the display as a float. 0.0 is off and 1.0 is full brightness. When
+//|     brightness: Any = ...
+//|     """The brightness of the display as a float. 0.0 is off and 1.0 is full brightness. When
 //|     `auto_brightness` is True, the value of `brightness` will change automatically.
-//|     If `brightness` is set, `auto_brightness` will be disabled and will be set to False.
+//|     If `brightness` is set, `auto_brightness` will be disabled and will be set to False."""
 //|
 STATIC mp_obj_t displayio_display_obj_get_brightness(mp_obj_t self_in) {
     displayio_display_obj_t *self = native_display(self_in);
@@ -310,12 +310,11 @@ const mp_obj_property_t displayio_display_brightness_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: auto_brightness
-//|
-//|     True when the display brightness is adjusted automatically, based on an ambient
+//|     auto_brightness: Any = ...
+//|     """True when the display brightness is adjusted automatically, based on an ambient
 //|     light sensor or other method. Note that some displays may have this set to True by default,
 //|     but not actually implement automatic brightness adjustment. `auto_brightness` is set to False
-//|     if `brightness` is set manually.
+//|     if `brightness` is set manually."""
 //|
 STATIC mp_obj_t displayio_display_obj_get_auto_brightness(mp_obj_t self_in) {
     displayio_display_obj_t *self = native_display(self_in);
@@ -342,9 +341,8 @@ const mp_obj_property_t displayio_display_auto_brightness_obj = {
 
 
 
-//|   .. attribute:: width
-//|
-//|	Gets the width of the board
+//|     width: Any = ...
+//|	    Gets the width of the board
 //|
 //|
 STATIC mp_obj_t displayio_display_obj_get_width(mp_obj_t self_in) {
@@ -360,9 +358,8 @@ const mp_obj_property_t displayio_display_width_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: height
-//|
-//|	Gets the height of the board
+//|     height: Any = ...
+//|	    """Gets the height of the board"""
 //|
 //|
 STATIC mp_obj_t displayio_display_obj_get_height(mp_obj_t self_in) {
@@ -378,9 +375,8 @@ const mp_obj_property_t displayio_display_height_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: rotation
-//|
-//|     The rotation of the display as an int in degrees.
+//|     rotation: Any = ...
+//|     """The rotation of the display as an int in degrees."""
 //|
 STATIC mp_obj_t displayio_display_obj_get_rotation(mp_obj_t self_in) {
     displayio_display_obj_t *self = native_display(self_in);
@@ -402,9 +398,8 @@ const mp_obj_property_t displayio_display_rotation_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: bus
-//|
-//|	The bus being used by the display
+//|     bus: Any = ...
+//|	    """The bus being used by the display"""
 //|
 //|
 STATIC mp_obj_t displayio_display_obj_get_bus(mp_obj_t self_in) {
@@ -421,12 +416,13 @@ const mp_obj_property_t displayio_display_bus_obj = {
 };
 
 
-//|   .. method:: fill_row(y, buffer)
+//|     def fill_row(self, y: int, buffer: bytearray) -> Any:
+//|         """Extract the pixels from a single row
 //|
-//|     Extract the pixels from a single row
+//|         :param int y: The top edge of the area
+//|         :param bytearray buffer: The buffer in which to place the pixel data"""
+//|         ...
 //|
-//|     :param int y: The top edge of the area
-//|     :param bytearray buffer: The buffer in which to place the pixel data
 STATIC mp_obj_t displayio_display_obj_fill_row(size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_y, ARG_buffer };
     static const mp_arg_t allowed_args[] = {
diff --git a/shared-bindings/displayio/EPaperDisplay.c b/shared-bindings/displayio/EPaperDisplay.c
index 1459c1680..8b03ddc06 100644
--- a/shared-bindings/displayio/EPaperDisplay.c
+++ b/shared-bindings/displayio/EPaperDisplay.c
@@ -39,55 +39,56 @@
 #include "shared-module/displayio/__init__.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: displayio
+//| class EPaperDisplay:
+//|     """.. currentmodule:: displayio
 //|
-//| :class:`EPaperDisplay` -- Manage updating an epaper display over a display bus
-//| ==============================================================================
+//|     :class:`EPaperDisplay` -- Manage updating an epaper display over a display bus
+//|     ==============================================================================
 //|
-//| This initializes an epaper display and connects it into CircuitPython. Unlike other
-//| objects in CircuitPython, EPaperDisplay objects live until `displayio.release_displays()`
-//| is called. This is done so that CircuitPython can use the display itself.
+//|     This initializes an epaper display and connects it into CircuitPython. Unlike other
+//|     objects in CircuitPython, EPaperDisplay objects live until `displayio.release_displays()`
+//|     is called. This is done so that CircuitPython can use the display itself.
 //|
-//| Most people should not use this class directly. Use a specific display driver instead that will
-//| contain the startup and shutdown sequences at minimum.
+//|     Most people should not use this class directly. Use a specific display driver instead that will
+//|     contain the startup and shutdown sequences at minimum."""
 //|
-//| .. class:: EPaperDisplay(display_bus, start_sequence, stop_sequence, *, width, height, ram_width, ram_height, colstart=0, rowstart=0, rotation=0, set_column_window_command=None, set_row_window_command=None, single_byte_bounds=False, write_black_ram_command, black_bits_inverted=False, write_color_ram_command=None, color_bits_inverted=False, highlight_color=0x000000, refresh_display_command, refresh_time=40, busy_pin=None, busy_state=True, seconds_per_frame=180, always_toggle_chip_select=False)
+//|     def __init__(self, display_bus: Any, start_sequence: buffer, stop_sequence: buffer, *, width: int, height: int, ram_width: int, ram_height: int, colstart: int = 0, rowstart: int = 0, rotation: int = 0, set_column_window_command: int = None, set_row_window_command: int = None, single_byte_bounds: Any = False, write_black_ram_command: int, black_bits_inverted: bool = False, write_color_ram_command: int = None, color_bits_inverted: bool = False, highlight_color: int = 0x000000, refresh_display_command: int, refresh_time: float = 40, busy_pin: microcontroller.Pin = None, busy_state: bool = True, seconds_per_frame: float = 180, always_toggle_chip_select: bool = False):
+//|         """Create a EPaperDisplay object on the given display bus (`displayio.FourWire` or `displayio.ParallelBus`).
 //|
-//|   Create a EPaperDisplay object on the given display bus (`displayio.FourWire` or `displayio.ParallelBus`).
+//|         The ``start_sequence`` and ``stop_sequence`` are bitpacked to minimize the ram impact. Every
+//|         command begins with a command byte followed by a byte to determine the parameter count and if
+//|         a delay is need after. When the top bit of the second byte is 1, the next byte will be the
+//|         delay time in milliseconds. The remaining 7 bits are the parameter count excluding any delay
+//|         byte. The third through final bytes are the remaining command parameters. The next byte will
+//|         begin a new command definition.
 //|
-//|   The ``start_sequence`` and ``stop_sequence`` are bitpacked to minimize the ram impact. Every
-//|   command begins with a command byte followed by a byte to determine the parameter count and if
-//|   a delay is need after. When the top bit of the second byte is 1, the next byte will be the
-//|   delay time in milliseconds. The remaining 7 bits are the parameter count excluding any delay
-//|   byte. The third through final bytes are the remaining command parameters. The next byte will
-//|   begin a new command definition.
-//|
-//|   :param display_bus: The bus that the display is connected to
-//|   :type display_bus: displayio.FourWire or displayio.ParallelBus
-//|   :param buffer start_sequence: Byte-packed initialization sequence.
-//|   :param buffer stop_sequence: Byte-packed initialization sequence.
-//|   :param int width: Width in pixels
-//|   :param int height: Height in pixels
-//|   :param int ram_width: RAM width in pixels
-//|   :param int ram_height: RAM height in pixels
-//|   :param int colstart: The index if the first visible column
-//|   :param int rowstart: The index if the first visible row
-//|   :param int rotation: The rotation of the display in degrees clockwise. Must be in 90 degree increments (0, 90, 180, 270)
-//|   :param int set_column_window_command: Command used to set the start and end columns to update
-//|   :param int set_row_window_command: Command used so set the start and end rows to update
-//|   :param int set_current_column_command: Command used to set the current column location
-//|   :param int set_current_row_command: Command used to set the current row location
-//|   :param int write_black_ram_command: Command used to write pixels values into the update region
-//|   :param bool black_bits_inverted: True if 0 bits are used to show black pixels. Otherwise, 1 means to show black.
-//|   :param int write_color_ram_command: Command used to write pixels values into the update region
-//|   :param bool color_bits_inverted: True if 0 bits are used to show the color. Otherwise, 1 means to show color.
-//|   :param int highlight_color: RGB888 of source color to highlight with third ePaper color.
-//|   :param int refresh_display_command: Command used to start a display refresh
-//|   :param float refresh_time: Time it takes to refresh the display before the stop_sequence should be sent. Ignored when busy_pin is provided.
-//|   :param microcontroller.Pin busy_pin: Pin used to signify the display is busy
-//|   :param bool busy_state: State of the busy pin when the display is busy
-//|   :param float seconds_per_frame: Minimum number of seconds between screen refreshes
-//|   :param bool always_toggle_chip_select: When True, chip select is toggled every byte
+//|         :param display_bus: The bus that the display is connected to
+//|         :type display_bus: displayio.FourWire or displayio.ParallelBus
+//|         :param buffer start_sequence: Byte-packed initialization sequence.
+//|         :param buffer stop_sequence: Byte-packed initialization sequence.
+//|         :param int width: Width in pixels
+//|         :param int height: Height in pixels
+//|         :param int ram_width: RAM width in pixels
+//|         :param int ram_height: RAM height in pixels
+//|         :param int colstart: The index if the first visible column
+//|         :param int rowstart: The index if the first visible row
+//|         :param int rotation: The rotation of the display in degrees clockwise. Must be in 90 degree increments (0, 90, 180, 270)
+//|         :param int set_column_window_command: Command used to set the start and end columns to update
+//|         :param int set_row_window_command: Command used so set the start and end rows to update
+//|         :param int set_current_column_command: Command used to set the current column location
+//|         :param int set_current_row_command: Command used to set the current row location
+//|         :param int write_black_ram_command: Command used to write pixels values into the update region
+//|         :param bool black_bits_inverted: True if 0 bits are used to show black pixels. Otherwise, 1 means to show black.
+//|         :param int write_color_ram_command: Command used to write pixels values into the update region
+//|         :param bool color_bits_inverted: True if 0 bits are used to show the color. Otherwise, 1 means to show color.
+//|         :param int highlight_color: RGB888 of source color to highlight with third ePaper color.
+//|         :param int refresh_display_command: Command used to start a display refresh
+//|         :param float refresh_time: Time it takes to refresh the display before the stop_sequence should be sent. Ignored when busy_pin is provided.
+//|         :param microcontroller.Pin busy_pin: Pin used to signify the display is busy
+//|         :param bool busy_state: State of the busy pin when the display is busy
+//|         :param float seconds_per_frame: Minimum number of seconds between screen refreshes
+//|         :param bool always_toggle_chip_select: When True, chip select is toggled every byte"""
+//|         ...
 //|
 STATIC mp_obj_t displayio_epaperdisplay_make_new(const mp_obj_type_t *type, size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_display_bus, ARG_start_sequence, ARG_stop_sequence, ARG_width, ARG_height, ARG_ram_width, ARG_ram_height, ARG_colstart, ARG_rowstart, ARG_rotation, ARG_set_column_window_command, ARG_set_row_window_command, ARG_set_current_column_command, ARG_set_current_row_command, ARG_write_black_ram_command, ARG_black_bits_inverted, ARG_write_color_ram_command, ARG_color_bits_inverted, ARG_highlight_color, ARG_refresh_display_command,  ARG_refresh_time, ARG_busy_pin, ARG_busy_state, ARG_seconds_per_frame, ARG_always_toggle_chip_select };
@@ -170,12 +171,13 @@ static displayio_epaperdisplay_obj_t* native_display(mp_obj_t display_obj) {
     return MP_OBJ_TO_PTR(native_display);
 }
 
-//|   .. method:: show(group)
+//|     def show(self, group: Group) -> Any:
+//|         """Switches to displaying the given group of layers. When group is None, the default
+//|         CircuitPython terminal will be shown.
 //|
-//|     Switches to displaying the given group of layers. When group is None, the default
-//|     CircuitPython terminal will be shown.
+//|         :param Group group: The group to show."""
+//|         ...
 //|
-//|     :param Group group: The group to show.
 STATIC mp_obj_t displayio_epaperdisplay_obj_show(mp_obj_t self_in, mp_obj_t group_in) {
     displayio_epaperdisplay_obj_t *self = native_display(self_in);
     displayio_group_t* group = NULL;
@@ -191,10 +193,10 @@ STATIC mp_obj_t displayio_epaperdisplay_obj_show(mp_obj_t self_in, mp_obj_t grou
 }
 MP_DEFINE_CONST_FUN_OBJ_2(displayio_epaperdisplay_show_obj, displayio_epaperdisplay_obj_show);
 
-//|   .. method:: refresh()
-//|
-//|     Refreshes the display immediately or raises an exception if too soon. Use
-//|     ``time.sleep(display.time_to_refresh)`` to sleep until a refresh can occur.
+//|     def refresh(self, ) -> Any:
+//|         """Refreshes the display immediately or raises an exception if too soon. Use
+//|         ``time.sleep(display.time_to_refresh)`` to sleep until a refresh can occur."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_epaperdisplay_obj_refresh(mp_obj_t self_in) {
     displayio_epaperdisplay_obj_t *self = native_display(self_in);
@@ -206,10 +208,8 @@ STATIC mp_obj_t displayio_epaperdisplay_obj_refresh(mp_obj_t self_in) {
 }
 MP_DEFINE_CONST_FUN_OBJ_1(displayio_epaperdisplay_refresh_obj, displayio_epaperdisplay_obj_refresh);
 
-//|   .. attribute:: time_to_refresh
-//|
-//|     Time, in fractional seconds, until the ePaper display can be refreshed.
-//|
+//|     time_to_refresh: Any = ...
+//|     """Time, in fractional seconds, until the ePaper display can be refreshed."""
 //|
 STATIC mp_obj_t displayio_epaperdisplay_obj_get_time_to_refresh(mp_obj_t self_in) {
     displayio_epaperdisplay_obj_t *self = native_display(self_in);
@@ -224,10 +224,8 @@ const mp_obj_property_t displayio_epaperdisplay_time_to_refresh_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: width
-//|
-//|	Gets the width of the display in pixels
-//|
+//|     width: Any = ...
+//|     """Gets the width of the display in pixels"""
 //|
 STATIC mp_obj_t displayio_epaperdisplay_obj_get_width(mp_obj_t self_in) {
     displayio_epaperdisplay_obj_t *self = native_display(self_in);
@@ -242,10 +240,8 @@ const mp_obj_property_t displayio_epaperdisplay_width_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: height
-//|
-//|	Gets the height of the display in pixels
-//|
+//|     height: Any = ...
+//|	    """Gets the height of the display in pixels"""
 //|
 STATIC mp_obj_t displayio_epaperdisplay_obj_get_height(mp_obj_t self_in) {
     displayio_epaperdisplay_obj_t *self = native_display(self_in);
@@ -260,10 +256,8 @@ const mp_obj_property_t displayio_epaperdisplay_height_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: bus
-//|
-//|	The bus being used by the display
-//|
+//|     bus: Any = ...
+//|	    """The bus being used by the display"""
 //|
 STATIC mp_obj_t displayio_epaperdisplay_obj_get_bus(mp_obj_t self_in) {
     displayio_epaperdisplay_obj_t *self = native_display(self_in);
diff --git a/shared-bindings/displayio/FourWire.c b/shared-bindings/displayio/FourWire.c
index 6ad162411..649045039 100644
--- a/shared-bindings/displayio/FourWire.c
+++ b/shared-bindings/displayio/FourWire.c
@@ -38,31 +38,32 @@
 #include "shared-module/displayio/__init__.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: displayio
+//| class FourWire:
+//|     """.. currentmodule:: displayio
 //|
-//| :class:`FourWire` -- Manage updating a display over SPI four wire protocol
-//| ==========================================================================
+//|     :class:`FourWire` -- Manage updating a display over SPI four wire protocol
+//|     ==========================================================================
 //|
-//| Manage updating a display over SPI four wire protocol in the background while Python code runs.
-//| It doesn't handle display initialization.
+//|     Manage updating a display over SPI four wire protocol in the background while Python code runs.
+//|     It doesn't handle display initialization."""
 //|
-//| .. class:: FourWire(spi_bus, *, command, chip_select, reset=None, baudrate=24000000, polarity=0, phase=0)
+//|     def __init__(self, spi_bus: busio.SPI, *, command: microcontroller.Pin, chip_select: microcontroller.Pin, reset: microcontroller.Pin = None, baudrate: int = 24000000, polarity: int = 0, phase: int = 0):
+//|         """Create a FourWire object associated with the given pins.
 //|
-//|   Create a FourWire object associated with the given pins.
+//|         The SPI bus and pins are then in use by the display until `displayio.release_displays()` is
+//|         called even after a reload. (It does this so CircuitPython can use the display after your code
+//|         is done.) So, the first time you initialize a display bus in code.py you should call
+//|         :py:func`displayio.release_displays` first, otherwise it will error after the first code.py run.
 //|
-//|   The SPI bus and pins are then in use by the display until `displayio.release_displays()` is
-//|   called even after a reload. (It does this so CircuitPython can use the display after your code
-//|   is done.) So, the first time you initialize a display bus in code.py you should call
-//|   :py:func`displayio.release_displays` first, otherwise it will error after the first code.py run.
-//|
-//|   :param busio.SPI spi_bus: The SPI bus that make up the clock and data lines
-//|   :param microcontroller.Pin command: Data or command pin
-//|   :param microcontroller.Pin chip_select: Chip select pin
-//|   :param microcontroller.Pin reset: Reset pin. When None only software reset can be used
-//|   :param int baudrate: Maximum baudrate in Hz for the display on the bus
-//|   :param int polarity: the base state of the clock line (0 or 1)
-//|   :param int phase: the edge of the clock that data is captured. First (0)
-//|       or second (1). Rising or falling depends on clock polarity.
+//|         :param busio.SPI spi_bus: The SPI bus that make up the clock and data lines
+//|         :param microcontroller.Pin command: Data or command pin
+//|         :param microcontroller.Pin chip_select: Chip select pin
+//|         :param microcontroller.Pin reset: Reset pin. When None only software reset can be used
+//|         :param int baudrate: Maximum baudrate in Hz for the display on the bus
+//|         :param int polarity: the base state of the clock line (0 or 1)
+//|         :param int phase: the edge of the clock that data is captured. First (0)
+//|             or second (1). Rising or falling depends on clock polarity."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_fourwire_make_new(const mp_obj_type_t *type, size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_spi_bus, ARG_command, ARG_chip_select, ARG_reset, ARG_baudrate, ARG_polarity, ARG_phase };
@@ -100,10 +101,10 @@ STATIC mp_obj_t displayio_fourwire_make_new(const mp_obj_type_t *type, size_t n_
     return self;
 }
 
-//|   .. method:: reset()
-//|
-//|     Performs a hardware reset via the reset pin. Raises an exception if called when no reset pin
-//|     is available.
+//|     def reset(self, ) -> Any:
+//|         """Performs a hardware reset via the reset pin. Raises an exception if called when no reset pin
+//|         is available."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_fourwire_obj_reset(mp_obj_t self_in) {
     displayio_fourwire_obj_t *self = self_in;
@@ -115,10 +116,10 @@ STATIC mp_obj_t displayio_fourwire_obj_reset(mp_obj_t self_in) {
 }
 MP_DEFINE_CONST_FUN_OBJ_1(displayio_fourwire_reset_obj, displayio_fourwire_obj_reset);
 
-//|   .. method:: send(command, data, *, toggle_every_byte=False)
-//|
-//|     Sends the given command value followed by the full set of data. Display state, such as
-//|     vertical scroll, set via ``send`` may or may not be reset once the code is done.
+//|     def send(self, command: Any, data: Any, *, toggle_every_byte: Any = False) -> Any:
+//|         """Sends the given command value followed by the full set of data. Display state, such as
+//|         vertical scroll, set via ``send`` may or may not be reset once the code is done."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_fourwire_obj_send(size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_command, ARG_data, ARG_toggle_every_byte };
diff --git a/shared-bindings/displayio/Group.c b/shared-bindings/displayio/Group.c
index dd7600eb9..36e137dc9 100644
--- a/shared-bindings/displayio/Group.c
+++ b/shared-bindings/displayio/Group.c
@@ -35,22 +35,23 @@
 #include "py/runtime.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: displayio
+//| class Group:
+//|     """.. currentmodule:: displayio
 //|
-//| :class:`Group` -- Group together sprites and subgroups
-//| ==========================================================================
+//|     :class:`Group` -- Group together sprites and subgroups
+//|     ==========================================================================
 //|
-//| Manage a group of sprites and groups and how they are inter-related.
+//|     Manage a group of sprites and groups and how they are inter-related."""
 //|
-//| .. class:: Group(*, max_size=4, scale=1, x=0, y=0)
+//|     def __init__(self, *, max_size: int = 4, scale: int = 1, x: int = 0, y: int = 0):
+//|         """Create a Group of a given size and scale. Scale is in one dimension. For example, scale=2
+//|         leads to a layer's pixel being 2x2 pixels when in the group.
 //|
-//|   Create a Group of a given size and scale. Scale is in one dimension. For example, scale=2
-//|   leads to a layer's pixel being 2x2 pixels when in the group.
-//|
-//|   :param int max_size: The maximum group size.
-//|   :param int scale: Scale of layer pixels in one dimension.
-//|   :param int x: Initial x position within the parent.
-//|   :param int y: Initial y position within the parent.
+//|         :param int max_size: The maximum group size.
+//|         :param int scale: Scale of layer pixels in one dimension.
+//|         :param int x: Initial x position within the parent.
+//|         :param int y: Initial y position within the parent."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_group_make_new(const mp_obj_type_t *type, size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_max_size, ARG_scale, ARG_x, ARG_y };
@@ -90,10 +91,9 @@ displayio_group_t* native_group(mp_obj_t group_obj) {
     return MP_OBJ_TO_PTR(native_group);
 }
 
-//|   .. attribute:: hidden
-//|
-//|     True when the Group and all of it's layers are not visible. When False, the Group's layers
-//|     are visible if they haven't been hidden.
+//|     hidden: Any = ...
+//|     """True when the Group and all of it's layers are not visible. When False, the Group's layers
+//|     are visible if they haven't been hidden."""
 //|
 STATIC mp_obj_t displayio_group_obj_get_hidden(mp_obj_t self_in) {
     displayio_group_t *self = native_group(self_in);
@@ -116,10 +116,9 @@ const mp_obj_property_t displayio_group_hidden_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: scale
-//|
-//|     Scales each pixel within the Group in both directions. For example, when scale=2 each pixel
-//|     will be represented by 2x2 pixels.
+//|     scale: Any = ...
+//|     """Scales each pixel within the Group in both directions. For example, when scale=2 each pixel
+//|     will be represented by 2x2 pixels."""
 //|
 STATIC mp_obj_t displayio_group_obj_get_scale(mp_obj_t self_in) {
     displayio_group_t *self = native_group(self_in);
@@ -146,9 +145,8 @@ const mp_obj_property_t displayio_group_scale_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: x
-//|
-//|     X position of the Group in the parent.
+//|     x: Any = ...
+//|     """X position of the Group in the parent."""
 //|
 STATIC mp_obj_t displayio_group_obj_get_x(mp_obj_t self_in) {
     displayio_group_t *self = native_group(self_in);
@@ -172,9 +170,8 @@ const mp_obj_property_t displayio_group_x_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: y
-//|
-//|     Y position of the Group in the parent.
+//|     y: Any = ...
+//|     """Y position of the Group in the parent."""
 //|
 STATIC mp_obj_t displayio_group_obj_get_y(mp_obj_t self_in) {
     displayio_group_t *self = native_group(self_in);
@@ -198,9 +195,9 @@ const mp_obj_property_t displayio_group_y_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. method:: append(layer)
-//|
-//|     Append a layer to the group. It will be drawn above other layers.
+//|     def append(self, layer: Any) -> Any:
+//|         """Append a layer to the group. It will be drawn above other layers."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_group_obj_append(mp_obj_t self_in, mp_obj_t layer) {
     displayio_group_t *self = native_group(self_in);
@@ -209,9 +206,9 @@ STATIC mp_obj_t displayio_group_obj_append(mp_obj_t self_in, mp_obj_t layer) {
 }
 MP_DEFINE_CONST_FUN_OBJ_2(displayio_group_append_obj, displayio_group_obj_append);
 
-//|   .. method:: insert(index, layer)
-//|
-//|     Insert a layer into the group.
+//|     def insert(self, index: Any, layer: Any) -> Any:
+//|         """Insert a layer into the group."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_group_obj_insert(mp_obj_t self_in, mp_obj_t index_obj, mp_obj_t layer) {
     displayio_group_t *self = native_group(self_in);
@@ -222,9 +219,9 @@ STATIC mp_obj_t displayio_group_obj_insert(mp_obj_t self_in, mp_obj_t index_obj,
 MP_DEFINE_CONST_FUN_OBJ_3(displayio_group_insert_obj, displayio_group_obj_insert);
 
 
-//|   .. method:: index(layer)
-//|
-//|     Returns the index of the first copy of layer. Raises ValueError if not found.
+//|     def index(self, layer: Any) -> Any:
+//|         """Returns the index of the first copy of layer. Raises ValueError if not found."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_group_obj_index(mp_obj_t self_in, mp_obj_t layer) {
     displayio_group_t *self = native_group(self_in);
@@ -236,9 +233,9 @@ STATIC mp_obj_t displayio_group_obj_index(mp_obj_t self_in, mp_obj_t layer) {
 }
 MP_DEFINE_CONST_FUN_OBJ_2(displayio_group_index_obj, displayio_group_obj_index);
 
-//|   .. method:: pop(i=-1)
-//|
-//|     Remove the ith item and return it.
+//|     def pop(self, i: Any = -1) -> Any:
+//|         """Remove the ith item and return it."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_group_obj_pop(size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_i };
@@ -259,9 +256,9 @@ STATIC mp_obj_t displayio_group_obj_pop(size_t n_args, const mp_obj_t *pos_args,
 MP_DEFINE_CONST_FUN_OBJ_KW(displayio_group_pop_obj, 1, displayio_group_obj_pop);
 
 
-//|   .. method:: remove(layer)
-//|
-//|     Remove the first copy of layer. Raises ValueError if it is not present.
+//|     def remove(self, layer: Any) -> Any:
+//|         """Remove the first copy of layer. Raises ValueError if it is not present."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_group_obj_remove(mp_obj_t self_in, mp_obj_t layer) {
     mp_obj_t index = displayio_group_obj_index(self_in, layer);
@@ -272,9 +269,9 @@ STATIC mp_obj_t displayio_group_obj_remove(mp_obj_t self_in, mp_obj_t layer) {
 }
 MP_DEFINE_CONST_FUN_OBJ_2(displayio_group_remove_obj, displayio_group_obj_remove);
 
-//|   .. method:: __len__()
-//|
-//|     Returns the number of layers in a Group
+//|     def __len__(self, ) -> Any:
+//|         """Returns the number of layers in a Group"""
+//|         ...
 //|
 STATIC mp_obj_t group_unary_op(mp_unary_op_t op, mp_obj_t self_in) {
     displayio_group_t *self = native_group(self_in);
@@ -286,29 +283,29 @@ STATIC mp_obj_t group_unary_op(mp_unary_op_t op, mp_obj_t self_in) {
     }
 }
 
-//|   .. method:: __getitem__(index)
-//|
-//|     Returns the value at the given index.
-//|
-//|     This allows you to::
-//|
-//|       print(group[0])
+//|     def __getitem__(self, index: Any) -> Any:
+//|         """Returns the value at the given index.
 //|
-//|   .. method:: __setitem__(index, value)
+//|         This allows you to::
 //|
-//|     Sets the value at the given index.
+//|           print(group[0])"""
+//|         ...
 //|
-//|     This allows you to::
+//|     def __setitem__(self, index: Any, value: Any) -> Any:
+//|         """Sets the value at the given index.
 //|
-//|       group[0] = sprite
+//|         This allows you to::
 //|
-//|   .. method:: __delitem__(index)
+//|           group[0] = sprite"""
+//|         ...
 //|
-//|     Deletes the value at the given index.
+//|     def __delitem__(self, index: Any) -> Any:
+//|         """Deletes the value at the given index.
 //|
-//|     This allows you to::
+//|         This allows you to::
 //|
-//|       del group[0]
+//|           del group[0]"""
+//|         ...
 //|
 STATIC mp_obj_t group_subscr(mp_obj_t self_in, mp_obj_t index_obj, mp_obj_t value) {
     displayio_group_t *self = native_group(self_in);
diff --git a/shared-bindings/displayio/I2CDisplay.c b/shared-bindings/displayio/I2CDisplay.c
index 963e8377c..e2402dc49 100644
--- a/shared-bindings/displayio/I2CDisplay.c
+++ b/shared-bindings/displayio/I2CDisplay.c
@@ -38,26 +38,27 @@
 #include "shared-module/displayio/__init__.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: displayio
+//| class I2CDisplay:
+//|     """.. currentmodule:: displayio
 //|
-//| :class:`I2CDisplay` -- Manage updating a display over I2C
-//| ==========================================================================
+//|     :class:`I2CDisplay` -- Manage updating a display over I2C
+//|     ==========================================================================
 //|
-//| Manage updating a display over I2C in the background while Python code runs.
-//| It doesn't handle display initialization.
+//|     Manage updating a display over I2C in the background while Python code runs.
+//|     It doesn't handle display initialization."""
 //|
-//| .. class:: I2CDisplay(i2c_bus, *, device_address, reset=None)
+//|     def __init__(self, i2c_bus: busio.I2C, *, device_address: int, reset: microcontroller.Pin = None):
+//|         """Create a I2CDisplay object associated with the given I2C bus and reset pin.
 //|
-//|   Create a I2CDisplay object associated with the given I2C bus and reset pin.
+//|         The I2C bus and pins are then in use by the display until `displayio.release_displays()` is
+//|         called even after a reload. (It does this so CircuitPython can use the display after your code
+//|         is done.) So, the first time you initialize a display bus in code.py you should call
+//|         :py:func`displayio.release_displays` first, otherwise it will error after the first code.py run.
 //|
-//|   The I2C bus and pins are then in use by the display until `displayio.release_displays()` is
-//|   called even after a reload. (It does this so CircuitPython can use the display after your code
-//|   is done.) So, the first time you initialize a display bus in code.py you should call
-//|   :py:func`displayio.release_displays` first, otherwise it will error after the first code.py run.
-//|
-//|   :param busio.I2C i2c_bus: The I2C bus that make up the clock and data lines
-//|   :param int device_address: The I2C address of the device
-//|   :param microcontroller.Pin reset: Reset pin. When None only software reset can be used
+//|         :param busio.I2C i2c_bus: The I2C bus that make up the clock and data lines
+//|         :param int device_address: The I2C address of the device
+//|         :param microcontroller.Pin reset: Reset pin. When None only software reset can be used"""
+//|         ...
 //|
 STATIC mp_obj_t displayio_i2cdisplay_make_new(const mp_obj_type_t *type, size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_i2c_bus, ARG_device_address, ARG_reset };
@@ -80,10 +81,10 @@ STATIC mp_obj_t displayio_i2cdisplay_make_new(const mp_obj_type_t *type, size_t
     return self;
 }
 
-//|   .. method:: reset()
-//|
-//|     Performs a hardware reset via the reset pin. Raises an exception if called when no reset pin
-//|     is available.
+//|     def reset(self, ) -> Any:
+//|         """Performs a hardware reset via the reset pin. Raises an exception if called when no reset pin
+//|         is available."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_i2cdisplay_obj_reset(mp_obj_t self_in) {
     displayio_i2cdisplay_obj_t *self = self_in;
@@ -95,10 +96,10 @@ STATIC mp_obj_t displayio_i2cdisplay_obj_reset(mp_obj_t self_in) {
 }
 MP_DEFINE_CONST_FUN_OBJ_1(displayio_i2cdisplay_reset_obj, displayio_i2cdisplay_obj_reset);
 
-//|   .. method:: send(command, data)
-//|
-//|     Sends the given command value followed by the full set of data. Display state, such as
-//|     vertical scroll, set via ``send`` may or may not be reset once the code is done.
+//|     def send(self, command: Any, data: Any) -> Any:
+//|         """Sends the given command value followed by the full set of data. Display state, such as
+//|         vertical scroll, set via ``send`` may or may not be reset once the code is done."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_i2cdisplay_obj_send(mp_obj_t self, mp_obj_t command_obj, mp_obj_t data_obj) {
     mp_int_t command_int = MP_OBJ_SMALL_INT_VALUE(command_obj);
diff --git a/shared-bindings/displayio/OnDiskBitmap.c b/shared-bindings/displayio/OnDiskBitmap.c
index 57179947e..95c890c3b 100644
--- a/shared-bindings/displayio/OnDiskBitmap.c
+++ b/shared-bindings/displayio/OnDiskBitmap.c
@@ -33,51 +33,52 @@
 #include "supervisor/shared/translate.h"
 #include "shared-bindings/displayio/OnDiskBitmap.h"
 
-//| .. currentmodule:: displayio
+//| class OnDiskBitmap:
+//|     """.. currentmodule:: displayio
 //|
-//| :class:`OnDiskBitmap` -- Loads pixels straight from disk
-//| ==========================================================================
+//|     :class:`OnDiskBitmap` -- Loads pixels straight from disk
+//|     ==========================================================================
 //|
-//| Loads values straight from disk. This minimizes memory use but can lead to
-//| much slower pixel load times. These load times may result in frame tearing where only part of
-//| the image is visible.
+//|     Loads values straight from disk. This minimizes memory use but can lead to
+//|     much slower pixel load times. These load times may result in frame tearing where only part of
+//|     the image is visible.
 //|
-//| It's easiest to use on a board with a built in display such as the `Hallowing M0 Express
-//| <https://www.adafruit.com/product/3900>`_.
+//|     It's easiest to use on a board with a built in display such as the `Hallowing M0 Express
+//|     <https://www.adafruit.com/product/3900>`_.
 //|
-//| .. code-block:: Python
+//|     .. code-block:: Python
 //|
-//|   import board
-//|   import displayio
-//|   import time
-//|   import pulseio
+//|       import board
+//|       import displayio
+//|       import time
+//|       import pulseio
 //|
-//|   board.DISPLAY.auto_brightness = False
-//|   board.DISPLAY.brightness = 0
-//|   splash = displayio.Group()
-//|   board.DISPLAY.show(splash)
+//|       board.DISPLAY.auto_brightness = False
+//|       board.DISPLAY.brightness = 0
+//|       splash = displayio.Group()
+//|       board.DISPLAY.show(splash)
 //|
-//|   with open("/sample.bmp", "rb") as f:
-//|       odb = displayio.OnDiskBitmap(f)
-//|       face = displayio.TileGrid(odb, pixel_shader=displayio.ColorConverter())
-//|       splash.append(face)
-//|       # Wait for the image to load.
-//|       board.DISPLAY.refresh(target_frames_per_second=60)
+//|       with open("/sample.bmp", "rb") as f:
+//|           odb = displayio.OnDiskBitmap(f)
+//|           face = displayio.TileGrid(odb, pixel_shader=displayio.ColorConverter())
+//|           splash.append(face)
+//|           # Wait for the image to load.
+//|           board.DISPLAY.refresh(target_frames_per_second=60)
 //|
-//|       # Fade up the backlight
-//|       for i in range(100):
-//|           board.DISPLAY.brightness = 0.01 * i
-//|           time.sleep(0.05)
+//|           # Fade up the backlight
+//|           for i in range(100):
+//|               board.DISPLAY.brightness = 0.01 * i
+//|               time.sleep(0.05)
 //|
-//|       # Wait forever
-//|       while True:
-//|           pass
+//|           # Wait forever
+//|           while True:
+//|               pass"""
 //|
-//| .. class:: OnDiskBitmap(file)
+//|     def __init__(self, file: file):
+//|         """Create an OnDiskBitmap object with the given file.
 //|
-//|   Create an OnDiskBitmap object with the given file.
-//|
-//|   :param file file: The open bitmap file
+//|         :param file file: The open bitmap file"""
+//|         ...
 //|
 STATIC mp_obj_t displayio_ondiskbitmap_make_new(const mp_obj_type_t *type, size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     mp_arg_check_num(n_args, kw_args, 1, 1, false);
@@ -93,9 +94,8 @@ STATIC mp_obj_t displayio_ondiskbitmap_make_new(const mp_obj_type_t *type, size_
     return MP_OBJ_FROM_PTR(self);
 }
 
-//|   .. attribute:: width
-//|
-//|      Width of the bitmap. (read only)
+//|     width: Any = ...
+//|     """Width of the bitmap. (read only)"""
 //|
 STATIC mp_obj_t displayio_ondiskbitmap_obj_get_width(mp_obj_t self_in) {
     displayio_ondiskbitmap_t *self = MP_OBJ_TO_PTR(self_in);
@@ -113,9 +113,8 @@ const mp_obj_property_t displayio_ondiskbitmap_width_obj = {
 
 };
 
-//|   .. attribute:: height
-//|
-//|      Height of the bitmap. (read only)
+//|     height: Any = ...
+//|     """Height of the bitmap. (read only)"""
 //|
 STATIC mp_obj_t displayio_ondiskbitmap_obj_get_height(mp_obj_t self_in) {
     displayio_ondiskbitmap_t *self = MP_OBJ_TO_PTR(self_in);
diff --git a/shared-bindings/displayio/Palette.c b/shared-bindings/displayio/Palette.c
index 67a7db85b..5df11d2b1 100644
--- a/shared-bindings/displayio/Palette.c
+++ b/shared-bindings/displayio/Palette.c
@@ -36,19 +36,27 @@
 #include "shared-bindings/util.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: displayio
+
+
+
+
+
+
+//| class Palette:
+//|     """.. currentmodule:: displayio
 //|
-//| :class:`Palette` -- Stores a mapping from bitmap pixel palette_indexes to display colors
-//| =========================================================================================
+//|     :class:`Palette` -- Stores a mapping from bitmap pixel palette_indexes to display colors
+//|     =========================================================================================
 //|
-//| Map a pixel palette_index to a full color. Colors are transformed to the display's format internally to
-//| save memory.
+//|     Map a pixel palette_index to a full color. Colors are transformed to the display's format internally to
+//|     save memory."""
 //|
-//| .. class:: Palette(color_count)
+//|     def __init__(self, color_count: int):
+//|         """Create a Palette object to store a set number of colors.
 //|
-//|   Create a Palette object to store a set number of colors.
+//|         :param int color_count: The number of colors in the Palette"""
+//|         ...
 //|
-//|   :param int color_count: The number of colors in the Palette
 // TODO(tannewt): Add support for other color formats.
 // TODO(tannewt): Add support for 8-bit alpha blending.
 //|
@@ -67,9 +75,9 @@ STATIC mp_obj_t displayio_palette_make_new(const mp_obj_type_t *type, size_t n_a
     return MP_OBJ_FROM_PTR(self);
 }
 
-//|   .. method:: __len__()
-//|
-//|     Returns the number of colors in a Palette
+//|     def __len__(self, ) -> Any:
+//|         """Returns the number of colors in a Palette"""
+//|         ...
 //|
 STATIC mp_obj_t group_unary_op(mp_unary_op_t op, mp_obj_t self_in) {
     displayio_palette_t *self = MP_OBJ_TO_PTR(self_in);
@@ -81,21 +89,21 @@ STATIC mp_obj_t group_unary_op(mp_unary_op_t op, mp_obj_t self_in) {
     }
 }
 
-//|   .. method:: __setitem__(index, value)
-//|
-//|     Sets the pixel color at the given index. The index should be an integer in the range 0 to color_count-1.
+//|     def __setitem__(self, index: Any, value: Any) -> Any:
+//|         """Sets the pixel color at the given index. The index should be an integer in the range 0 to color_count-1.
 //|
-//|     The value argument represents a color, and can be from 0x000000 to 0xFFFFFF (to represent an RGB value).
-//|     Value can be an int, bytes (3 bytes (RGB) or 4 bytes (RGB + pad byte)), bytearray,
-//|     or a tuple or list of 3 integers.
+//|         The value argument represents a color, and can be from 0x000000 to 0xFFFFFF (to represent an RGB value).
+//|         Value can be an int, bytes (3 bytes (RGB) or 4 bytes (RGB + pad byte)), bytearray,
+//|         or a tuple or list of 3 integers.
 //|
-//|     This allows you to::
+//|         This allows you to::
 //|
-//|       palette[0] = 0xFFFFFF                     # set using an integer
-//|       palette[1] = b'\xff\xff\x00'              # set using 3 bytes
-//|       palette[2] = b'\xff\xff\x00\x00'          # set using 4 bytes
-//|       palette[3] = bytearray(b'\x00\x00\xFF')   # set using a bytearay of 3 or 4 bytes
-//|       palette[4] = (10, 20, 30)                 # set using a tuple of 3 integers
+//|           palette[0] = 0xFFFFFF                     # set using an integer
+//|           palette[1] = b'\xff\xff\x00'              # set using 3 bytes
+//|           palette[2] = b'\xff\xff\x00\x00'          # set using 4 bytes
+//|           palette[3] = bytearray(b'\x00\x00\xFF')   # set using a bytearay of 3 or 4 bytes
+//|           palette[4] = (10, 20, 30)                 # set using a tuple of 3 integers"""
+//|         ...
 //|
 STATIC mp_obj_t palette_subscr(mp_obj_t self_in, mp_obj_t index_in, mp_obj_t value) {
     if (value == MP_OBJ_NULL) {
@@ -144,7 +152,7 @@ STATIC mp_obj_t palette_subscr(mp_obj_t self_in, mp_obj_t index_in, mp_obj_t val
     return mp_const_none;
 }
 
-//|   .. method:: make_transparent(palette_index)
+//|     def make_transparent(self, palette_index: Any) -> Any: ...
 //|
 STATIC mp_obj_t displayio_palette_obj_make_transparent(mp_obj_t self_in, mp_obj_t palette_index_obj) {
     displayio_palette_t *self = MP_OBJ_TO_PTR(self_in);
@@ -158,7 +166,7 @@ STATIC mp_obj_t displayio_palette_obj_make_transparent(mp_obj_t self_in, mp_obj_
 }
 MP_DEFINE_CONST_FUN_OBJ_2(displayio_palette_make_transparent_obj, displayio_palette_obj_make_transparent);
 
-//|   .. method:: make_opaque(palette_index)
+//|     def make_opaque(self, palette_index: Any) -> Any: ...
 //|
 STATIC mp_obj_t displayio_palette_obj_make_opaque(mp_obj_t self_in, mp_obj_t palette_index_obj) {
     displayio_palette_t *self = MP_OBJ_TO_PTR(self_in);
diff --git a/shared-bindings/displayio/ParallelBus.c b/shared-bindings/displayio/ParallelBus.c
index bdafdaef6..cedcf1de5 100644
--- a/shared-bindings/displayio/ParallelBus.c
+++ b/shared-bindings/displayio/ParallelBus.c
@@ -37,31 +37,32 @@
 #include "shared-module/displayio/__init__.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: displayio
+//| class ParallelBus:
+//|     """.. currentmodule:: displayio
 //|
-//| :class:`ParallelBus` -- Manage updating a display over 8-bit parallel bus
-//| ==============================================================================
+//|     :class:`ParallelBus` -- Manage updating a display over 8-bit parallel bus
+//|     ==============================================================================
 //|
-//| Manage updating a display over 8-bit parallel bus in the background while Python code runs. This
-//| protocol may be refered to as 8080-I Series Parallel Interface in datasheets. It doesn't handle
-//| display initialization.
+//|     Manage updating a display over 8-bit parallel bus in the background while Python code runs. This
+//|     protocol may be refered to as 8080-I Series Parallel Interface in datasheets. It doesn't handle
+//|     display initialization."""
 //|
-//| .. class:: ParallelBus(*, data0, command, chip_select, write, read, reset)
+//|     def __init__(self, *, data0: microcontroller.Pin, command: microcontroller.Pin, chip_select: microcontroller.Pin, write: microcontroller.Pin, read: microcontroller.Pin, reset: microcontroller.Pin):
+//|         """Create a ParallelBus object associated with the given pins. The bus is inferred from data0
+//|         by implying the next 7 additional pins on a given GPIO port.
 //|
-//|   Create a ParallelBus object associated with the given pins. The bus is inferred from data0
-//|   by implying the next 7 additional pins on a given GPIO port.
+//|         The parallel bus and pins are then in use by the display until `displayio.release_displays()`
+//|         is called even after a reload. (It does this so CircuitPython can use the display after your
+//|         code is done.) So, the first time you initialize a display bus in code.py you should call
+//|         :py:func`displayio.release_displays` first, otherwise it will error after the first code.py run.
 //|
-//|   The parallel bus and pins are then in use by the display until `displayio.release_displays()`
-//|   is called even after a reload. (It does this so CircuitPython can use the display after your
-//|   code is done.) So, the first time you initialize a display bus in code.py you should call
-//|   :py:func`displayio.release_displays` first, otherwise it will error after the first code.py run.
-//|
-//|   :param microcontroller.Pin data0: The first data pin. The rest are implied
-//|   :param microcontroller.Pin command: Data or command pin
-//|   :param microcontroller.Pin chip_select: Chip select pin
-//|   :param microcontroller.Pin write: Write pin
-//|   :param microcontroller.Pin read: Read pin
-//|   :param microcontroller.Pin reset: Reset pin
+//|         :param microcontroller.Pin data0: The first data pin. The rest are implied
+//|         :param microcontroller.Pin command: Data or command pin
+//|         :param microcontroller.Pin chip_select: Chip select pin
+//|         :param microcontroller.Pin write: Write pin
+//|         :param microcontroller.Pin read: Read pin
+//|         :param microcontroller.Pin reset: Reset pin"""
+//|         ...
 //|
 STATIC mp_obj_t displayio_parallelbus_make_new(const mp_obj_type_t *type, size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_data0, ARG_command, ARG_chip_select, ARG_write, ARG_read, ARG_reset };
@@ -90,11 +91,12 @@ STATIC mp_obj_t displayio_parallelbus_make_new(const mp_obj_type_t *type, size_t
     return self;
 }
 
-//|   .. method:: reset()
-//|
-//|     Performs a hardware reset via the reset pin. Raises an exception if called when no reset pin
-//|     is available.
+//|     def reset(self, ) -> Any:
+//|         """Performs a hardware reset via the reset pin. Raises an exception if called when no reset pin
+//|         is available."""
+//|         ...
 //|
+
 STATIC mp_obj_t displayio_parallelbus_obj_reset(mp_obj_t self_in) {
     displayio_parallelbus_obj_t *self = self_in;
 
@@ -105,10 +107,10 @@ STATIC mp_obj_t displayio_parallelbus_obj_reset(mp_obj_t self_in) {
 }
 MP_DEFINE_CONST_FUN_OBJ_1(displayio_parallelbus_reset_obj, displayio_parallelbus_obj_reset);
 
-//|   .. method:: send(command, data)
-//|
-//|     Sends the given command value followed by the full set of data. Display state, such as
-//|     vertical scroll, set via ``send`` may or may not be reset once the code is done.
+//|     def send(self, command: Any, data: Any) -> Any:
+//|         """Sends the given command value followed by the full set of data. Display state, such as
+//|         vertical scroll, set via ``send`` may or may not be reset once the code is done."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_parallelbus_obj_send(mp_obj_t self, mp_obj_t command_obj, mp_obj_t data_obj) {
     mp_int_t command_int = MP_OBJ_SMALL_INT_VALUE(command_obj);
diff --git a/shared-bindings/displayio/Shape.c b/shared-bindings/displayio/Shape.c
index 7c7b10501..0f22bb2a3 100644
--- a/shared-bindings/displayio/Shape.c
+++ b/shared-bindings/displayio/Shape.c
@@ -34,22 +34,23 @@
 #include "shared-bindings/util.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: displayio
+//| class Shape:
+//|     """.. currentmodule:: displayio
 //|
-//| :class:`Shape` -- Represents a shape by defining its bounds on each row
-//| ==========================================================================
+//|     :class:`Shape` -- Represents a shape by defining its bounds on each row
+//|     ==========================================================================
 //|
-//| Represents any shape made by defining boundaries that may be mirrored.
+//|     Represents any shape made by defining boundaries that may be mirrored."""
 //|
-//| .. class:: Shape(width, height, *, mirror_x=False, mirror_y=False)
+//|     def __init__(self, width: int, height: int, *, mirror_x: bool = False, mirror_y: bool = False):
+//|         """Create a Shape object with the given fixed size. Each pixel is one bit and is stored by the
+//|         column boundaries of the shape on each row. Each row's boundary defaults to the full row.
 //|
-//|   Create a Shape object with the given fixed size. Each pixel is one bit and is stored by the
-//|   column boundaries of the shape on each row. Each row's boundary defaults to the full row.
-//|
-//|   :param int width: The number of pixels wide
-//|   :param int height: The number of pixels high
-//|   :param bool mirror_x: When true the left boundary is mirrored to the right.
-//|   :param bool mirror_y: When true the top boundary is mirrored to the bottom.
+//|         :param int width: The number of pixels wide
+//|         :param int height: The number of pixels high
+//|         :param bool mirror_x: When true the left boundary is mirrored to the right.
+//|         :param bool mirror_y: When true the top boundary is mirrored to the bottom."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_shape_make_new(const mp_obj_type_t *type, size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_width, ARG_height, ARG_mirror_x, ARG_mirror_y };
@@ -83,9 +84,9 @@ STATIC mp_obj_t displayio_shape_make_new(const mp_obj_type_t *type, size_t n_arg
 }
 
 
-//|   .. method:: set_boundary(y, start_x, end_x)
-//|
-//|     Loads pre-packed data into the given row.
+//|     def set_boundary(self, y: Any, start_x: Any, end_x: Any) -> Any:
+//|         """Loads pre-packed data into the given row."""
+//|         ...
 //|
 STATIC mp_obj_t displayio_shape_obj_set_boundary(size_t n_args, const mp_obj_t *args) {
     (void) n_args;
diff --git a/shared-bindings/displayio/TileGrid.c b/shared-bindings/displayio/TileGrid.c
index 288eb4b23..e7410e4b6 100644
--- a/shared-bindings/displayio/TileGrid.c
+++ b/shared-bindings/displayio/TileGrid.c
@@ -40,33 +40,33 @@
 #include "shared-bindings/displayio/Shape.h"
 #include "supervisor/shared/translate.h"
 
-//| .. currentmodule:: displayio
+//| class TileGrid:
+//|     """.. currentmodule:: displayio
 //|
-//| :class:`TileGrid` -- A grid of tiles sourced out of one bitmap
-//| ==========================================================================
+//|     :class:`TileGrid` -- A grid of tiles sourced out of one bitmap
+//|     ==========================================================================
 //|
-//| Position a grid of tiles sourced from a bitmap and pixel_shader combination. Multiple grids
-//| can share bitmaps and pixel shaders.
+//|     Position a grid of tiles sourced from a bitmap and pixel_shader combination. Multiple grids
+//|     can share bitmaps and pixel shaders.
 //|
-//| A single tile grid is also known as a Sprite.
+//|     A single tile grid is also known as a Sprite."""
 //|
-//| .. class:: TileGrid(bitmap, *, pixel_shader, width=1, height=1, tile_width=None, tile_height=None, default_tile=0, x=0, y=0)
+//|     def __init__(self, bitmap: displayio.Bitmap, *, pixel_shader: displayio.Palette, width: int = 1, height: int = 1, tile_width: int = None, tile_height: int = None, default_tile: int = 0, x: int = 0, y: int = 0):
+//|         """Create a TileGrid object. The bitmap is source for 2d pixels. The pixel_shader is used to
+//|         convert the value and its location to a display native pixel color. This may be a simple color
+//|         palette lookup, a gradient, a pattern or a color transformer.
 //|
-//|   Create a TileGrid object. The bitmap is source for 2d pixels. The pixel_shader is used to
-//|   convert the value and its location to a display native pixel color. This may be a simple color
-//|   palette lookup, a gradient, a pattern or a color transformer.
+//|         tile_width and tile_height match the height of the bitmap by default.
 //|
-//|   tile_width and tile_height match the height of the bitmap by default.
-//|
-//|   :param displayio.Bitmap bitmap: The bitmap storing one or more tiles.
-//|   :param displayio.Palette pixel_shader: The pixel shader that produces colors from values
-//|   :param int width: Width of the grid in tiles.
-//|   :param int height: Height of the grid in tiles.
-//|   :param int tile_width: Width of a single tile in pixels. Defaults to the full Bitmap and must evenly divide into the Bitmap's dimensions.
-//|   :param int tile_height: Height of a single tile in pixels. Defaults to the full Bitmap and must evenly divide into the Bitmap's dimensions.
-//|   :param int default_tile: Default tile index to show.
-//|   :param int x: Initial x position of the left edge within the parent.
-//|   :param int y: Initial y position of the top edge within the parent.
+//|         :param displayio.Bitmap bitmap: The bitmap storing one or more tiles.
+//|         :param displayio.Palette pixel_shader: The pixel shader that produces colors from values
+//|         :param int width: Width of the grid in tiles.
+//|         :param int height: Height of the grid in tiles.
+//|         :param int tile_width: Width of a single tile in pixels. Defaults to the full Bitmap and must evenly divide into the Bitmap's dimensions.
+//|         :param int tile_height: Height of a single tile in pixels. Defaults to the full Bitmap and must evenly divide into the Bitmap's dimensions.
+//|         :param int default_tile: Default tile index to show.
+//|         :param int x: Initial x position of the left edge within the parent.
+//|         :param int y: Initial y position of the top edge within the parent."""
 //|
 STATIC mp_obj_t displayio_tilegrid_make_new(const mp_obj_type_t *type, size_t n_args, const mp_obj_t *pos_args, mp_map_t *kw_args) {
     enum { ARG_bitmap, ARG_pixel_shader, ARG_width, ARG_height, ARG_tile_width, ARG_tile_height, ARG_default_tile, ARG_x, ARG_y };
@@ -144,9 +144,8 @@ static displayio_tilegrid_t* native_tilegrid(mp_obj_t tilegrid_obj) {
     mp_obj_assert_native_inited(native_tilegrid);
     return MP_OBJ_TO_PTR(native_tilegrid);
 }
-//|   .. attribute:: hidden
-//|
-//|     True when the TileGrid is hidden. This may be False even when a part of a hidden Group.
+//|     hidden: Any = ...
+//|     """True when the TileGrid is hidden. This may be False even when a part of a hidden Group."""
 //|
 STATIC mp_obj_t displayio_tilegrid_obj_get_hidden(mp_obj_t self_in) {
     displayio_tilegrid_t *self = native_tilegrid(self_in);
@@ -169,9 +168,8 @@ const mp_obj_property_t displayio_tilegrid_hidden_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: x
-//|
-//|     X position of the left edge in the parent.
+//|     x: Any = ...
+//|     """X position of the left edge in the parent."""
 //|
 STATIC mp_obj_t displayio_tilegrid_obj_get_x(mp_obj_t self_in) {
     displayio_tilegrid_t *self = native_tilegrid(self_in);
@@ -195,9 +193,8 @@ const mp_obj_property_t displayio_tilegrid_x_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: y
-//|
-//|     Y position of the top edge in the parent.
+//|     y: Any = ...
+//|     """Y position of the top edge in the parent."""
 //|
 STATIC mp_obj_t displayio_tilegrid_obj_get_y(mp_obj_t self_in) {
     displayio_tilegrid_t *self = native_tilegrid(self_in);
@@ -221,9 +218,8 @@ const mp_obj_property_t displayio_tilegrid_y_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: flip_x
-//|
-//|     If true, the left edge rendered will be the right edge of the right-most tile.
+//|     flip_x: Any = ...
+//|     """If true, the left edge rendered will be the right edge of the right-most tile."""
 //|
 STATIC mp_obj_t displayio_tilegrid_obj_get_flip_x(mp_obj_t self_in) {
     displayio_tilegrid_t *self = native_tilegrid(self_in);
@@ -246,9 +242,8 @@ const mp_obj_property_t displayio_tilegrid_flip_x_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: flip_y
-//|
-//|     If true, the top edge rendered will be the bottom edge of the bottom-most tile.
+//|     flip_y: Any = ...
+//|     """If true, the top edge rendered will be the bottom edge of the bottom-most tile."""
 //|
 STATIC mp_obj_t displayio_tilegrid_obj_get_flip_y(mp_obj_t self_in) {
     displayio_tilegrid_t *self = native_tilegrid(self_in);
@@ -272,10 +267,9 @@ const mp_obj_property_t displayio_tilegrid_flip_y_obj = {
 };
 
 
-//|   .. attribute:: transpose_xy
-//|
-//|     If true, the TileGrid's axis will be swapped. When combined with mirroring, any 90 degree
-//|     rotation can be achieved along with the corresponding mirrored version.
+//|     transpose_xy: Any = ...
+//|     """If true, the TileGrid's axis will be swapped. When combined with mirroring, any 90 degree
+//|     rotation can be achieved along with the corresponding mirrored version."""
 //|
 STATIC mp_obj_t displayio_tilegrid_obj_get_transpose_xy(mp_obj_t self_in) {
     displayio_tilegrid_t *self = native_tilegrid(self_in);
@@ -298,9 +292,8 @@ const mp_obj_property_t displayio_tilegrid_transpose_xy_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. attribute:: pixel_shader
-//|
-//|     The pixel shader of the tilegrid.
+//|     pixel_shader: Any = ...
+//|     """The pixel shader of the tilegrid."""
 //|
 STATIC mp_obj_t displayio_tilegrid_obj_get_pixel_shader(mp_obj_t self_in) {
     displayio_tilegrid_t *self = native_tilegrid(self_in);
@@ -327,27 +320,27 @@ const mp_obj_property_t displayio_tilegrid_pixel_shader_obj = {
               (mp_obj_t)&mp_const_none_obj},
 };
 
-//|   .. method:: __getitem__(index)
-//|
-//|     Returns the tile index at the given index. The index can either be an x,y tuple or an int equal
-//|     to ``y * width + x``.
-//|
-//|     This allows you to::
+//|     def __getitem__(self, index: Any) -> Any:
+//|         """Returns the tile index at the given index. The index can either be an x,y tuple or an int equal
+//|         to ``y * width + x``.
 //|
-//|       print(grid[0])
+//|         This allows you to::
 //|
-//|   .. method:: __setitem__(index, tile_index)
+//|           print(grid[0])"""
+//|         ...
 //|
-//|     Sets the tile index at the given index. The index can either be an x,y tuple or an int equal
-//|     to ``y * width + x``.
+//|     def __setitem__(self, index: Any, tile_index: Any) -> Any:
+//|         """Sets the tile index at the given index. The index can either be an x,y tuple or an int equal
+//|         to ``y * width + x``.
 //|
-//|     This allows you to::
+//|         This allows you to::
 //|
-//|       grid[0] = 10
+//|           grid[0] = 10
 //|
-//|     or::
+//|         or::
 //|
-//|       grid[0,0] = 10
+//|           grid[0,0] = 10"""
+//|         ...
 //|
 STATIC mp_obj_t tilegrid_subscr(mp_obj_t self_in, mp_obj_t index_obj, mp_obj_t value_obj) {
     displayio_tilegrid_t *self = native_tilegrid(self_in);
diff --git a/shared-bindings/displayio/__init__.c b/shared-bindings/displayio/__init__.c
index f78325593..37c025329 100644
--- a/shared-bindings/displayio/__init__.c
+++ b/shared-bindings/displayio/__init__.c
@@ -43,7 +43,7 @@
 #include "shared-bindings/displayio/Shape.h"
 #include "shared-bindings/displayio/TileGrid.h"
 
-//| :mod:`displayio` --- Native display driving
+//| """:mod:`displayio` --- Native display driving
 //| =========================================================================
 //|
 //| .. module:: displayio
@@ -69,18 +69,18 @@
 //|     Palette
 //|     ParallelBus
 //|     Shape
-//|     TileGrid
+//|     TileGrid"""
 //|
 
 
-//| .. function:: release_displays()
+//| def release_displays() -> Any:
+//|     """Releases any actively used displays so their busses and pins can be used again. This will also
+//|     release the builtin display on boards that have one. You will need to reinitialize it yourself
+//|     afterwards. This may take seconds to complete if an active EPaperDisplay is refreshing.
 //|
-//|   Releases any actively used displays so their busses and pins can be used again. This will also
-//|   release the builtin display on boards that have one. You will need to reinitialize it yourself
-//|   afterwards. This may take seconds to complete if an active EPaperDisplay is refreshing.
-//|
-//|   Use this once in your code.py if you initialize a display. Place it right before the
-//|   initialization so the display is active as long as possible.
+//|     Use this once in your code.py if you initialize a display. Place it right before the
+//|     initialization so the display is active as long as possible."""
+//|     ...
 //|
 STATIC mp_obj_t displayio_release_displays(void) {
     common_hal_displayio_release_displays();