diff options
| -rw-r--r-- | ports/nrf/boards/TG-Watch02A/README.md | 201 | ||||
| -rw-r--r-- | ports/nrf/boards/TG-Watch02A/board.c | 38 | ||||
| -rw-r--r-- | ports/nrf/boards/TG-Watch02A/mpconfigboard.h | 72 | ||||
| -rw-r--r-- | ports/nrf/boards/TG-Watch02A/mpconfigboard.mk | 26 | ||||
| -rw-r--r-- | ports/nrf/boards/TG-Watch02A/pins.c | 53 | ||||
| -rw-r--r-- | ports/nrf/boards/pca10056/mpconfigboard.h | 1 |
6 files changed, 391 insertions, 0 deletions
diff --git a/ports/nrf/boards/TG-Watch02A/README.md b/ports/nrf/boards/TG-Watch02A/README.md new file mode 100644 index 000000000..8d515010f --- /dev/null +++ b/ports/nrf/boards/TG-Watch02A/README.md @@ -0,0 +1,201 @@ +# Setup + +The `feather52840` board is currently based on the `PCA10056` development +board from Nordic Semiconductors, since commercial modules are not yet +available for the nRF52840. + +The difference between the `pca10056` and `feather52840` board support +packages is that no bootloader is present on the `pca10056` (a HW debugger +like a Segger J-Link is required to flash firmware images), whereas the +`feather52840` package uses a serial bootloader, with a slightly different +flash layout to account for the bootloader's presence. + +Both targets run on the same hardware and assume the same pinouts. + +The `feather52840` board support package will be updated at a later date +to reflect any pin changes in the final Feather form-factor HW. + +## Installing CircuitPython submodules + +Before you can build, you will need to run the following commands once, which +will install the submodules that are part of the CircuitPython ecosystem, and +build the `mpy-cross` tool: + +``` +$ cd circuitpython +$ git submodule update --init +$ make -C mpy-cross +``` + +You then need to download the SD and Nordic SDK files via: + +> This script relies on `wget`, which must be available from the command line. + +``` +$ cd ports/nrf +$ ./bluetooth/download_ble_stack.sh +``` + +## Installing the Serial Bootloader + +The Adafruit nRF52840 Feather uses a serial bootloader that allows you to +update the core CircuitPython firmware and internal file system contents +using only a serial connection. + +On empty devices, the serial bootloader will need to be flashed once using a +HW debugger such as a Segger J-Link before the serial updater (`adafruit-nrfutil`) can +be used. + +### Install `nrfjprog` + +Before you can install the bootloader, you will first need to install the +`nrfjprog` tool from Nordic Semiconductors for your operating system. The +binary files can be downloaded via the following links: + +- [nRF5x toolset tar for Linux 32-bit v9.7.2](http://www.nordicsemi.com/eng/nordic/Products/nRF52832/nRF5x-Command-Line-Tools-Linux32/52619) +- [nRF5x toolset tar for Linux 64-bit v9.7.2](http://www.nordicsemi.com/eng/nordic/Products/nRF52832/nRF5x-Command-Line-Tools-Linux64/51388) +- [nRF5x toolset tar for OSX v9.7.2](http://www.nordicsemi.com/eng/nordic/Products/nRF52832/nRF5x-Command-Line-Tools-OSX/53406) +- [nRF5x toolset installer for Windows v9.7.2](http://www.nordicsemi.com/eng/nordic/Products/nRF52832/nRF5x-Command-Line-Tools-Win32/48768) + +You will then need to add the `nrfjprog` folder to your system `PATH` variable +so that it is available from the command line. The exact process for this is +OS specific, but on a POSIX type system like OS X or Linux, you can +temporarily add the location to your `PATH` environment variables as follows: + +``` +$ export PATH=$PATH:YOURPATHHERE/nRF5x-Command-Line-Tools_9_7_2_OSX/nrfjprog/ +``` + +You can test this by running the following command: + +``` +$ nrfjprog --version +nrfjprog version: 9.7.2 +JLinkARM.dll version: 6.20f +``` + +### Flash the USB CDC Bootloader with 'nrfjprog' + +> This operation only needs to be done once, and only on boards that don't + already have the serial bootloader installed. + +Firstly clone the [Adafruit_nRF52_Bootloader](https://github.com/adafruit/Adafruit_nRF52_Bootloader.git) and enter its directory + +``` +$ git clone https://github.com/adafruit/Adafruit_nRF52_Bootloader.git +$ cd Adafruit_nRF52_Bootloader +``` + +Once `nrfjprog` is installed and available in `PATH` you can flash your +board with the serial bootloader via the following command: + +``` +make BOARD=feather_nrf52840_express VERSION=latest flash +``` + +This should give you the following (or very similar) output, and you will see +a DFU blinky pattern on one of the board LEDs: + +``` +$ make BOARD=pca10056 VERSION=latest flash +Flashing: bin/pca10056/6.0.0r0/pca10056_bootloader_s140_6.0.0r0.hex +nrfjprog --program bin/pca10056/6.0.0r0/pca10056_bootloader_s140_6.0.0r0.hex --chiperase -f nrf52 --reset +Parsing hex file. +Erasing user available code and UICR flash areas. +Applying system reset. +Checking that the area to write is not protected. +Programing device. +Applying system reset. +Run. +``` + +From this point onward, you can now use a simple serial port for firmware +updates. + +Note: You can specify other version that are available in the directory `Adafruit_nRF52_Bootloader/bin/feather_nrf52840_express/` . The `VERSION=latest` will use the latest bootloader available. + +### IMPORTANT: Disable Mass Storage on PCA10056 J-Link + +The J-Link firmware on the PCA10056 implement USB Mass Storage, but this +causes a known conflict with reliable USB CDC serial port communication. In +order to use the serial bootloader, **you must disable MSD support on the +Segger J-Link**! + +To disable mass storage support, run the `JLinkExe` (or equivalent) command, +and send `MSDDisable`. (You can re-enable MSD support via `MSDEnable`): + +``` +$ JLinkExe +SEGGER J-Link Commander V6.20f (Compiled Oct 13 2017 17:20:01) +DLL version V6.20f, compiled Oct 13 2017 17:19:52 + +Connecting to J-Link via USB...O.K. +Firmware: J-Link OB-SAM3U128-V2-NordicSemi compiled Jul 24 2017 17:30:12 +Hardware version: V1.00 +S/N: 683947110 +VTref = 3.300V + + +Type "connect" to establish a target connection, '?' for help +J-Link>MSDDisable +Probe configured successfully. +J-Link>exit +``` + +## Building and Flashing CircuitPython + +### Installing `adafruit-nrfutil` + +run follow command to install [adafruit-nrfutil](https://github.com/adafruit/Adafruit_nRF52_nrfutil) from PyPi + +``` +$ pip3 install adafruit-nrfutil --user +``` + +### Flashing CircuitPython with USB CDC + +With the serial bootloader present on your board, you first need to force your +board into DFU mode by holding down BUTTON1 and RESETTING the board (with +BUTTON1 still pressed as you come out of reset). + +This will give you a **fast blinky DFU pattern** to indicate you are in DFU +mode. + +You can **build and flash** a CircuitPython binary via the following command: + +``` +$ make V=1 SD=s140 SERIAL=/dev/tty.usbmodem1411 BOARD=feather52840 all dfu-gen dfu-flash +``` + +This should give you the following results: + +``` +$make V=1 BOARD=feather52840 SD=s140 SERIAL=/dev/tty.usbmodem1411 dfu-gen dfu-flash +nrfutil dfu genpkg --sd-req 0xFFFE --dev-type 0x0052 --application build-feather52840-s140/firmware.hex build-feather52840-s140/dfu-package.zip +Zip created at build-feather52840-s140/dfu-package.zip +nrfutil --verbose dfu serial --package build-feather52840-s140/dfu-package.zip -p /dev/ttyACM1 -b 115200 --singlebank +Upgrading target on /dev/ttyACM1 with DFU package /home/hathach/Dropbox/adafruit/circuitpython/ada_cp/ports/nrf/build-feather52840-s140/dfu-package.zip. Flow control is disabled, Single bank mode +Starting DFU upgrade of type 4, SoftDevice size: 0, bootloader size: 0, application size: 199840 +Sending DFU start packet +Sending DFU init packet +Sending firmware file +######################################################################################################################################################################################################################################################################################################################################################################################################### +Activating new firmware + +DFU upgrade took 8.50606513023s +Device programmed. +``` + +### Flashing CircuitPython with MSC UF2 + +uf2 file is generated last by `all` target + +``` +$ make V=1 SD=s140 SERIAL=/dev/tty.usbmodem1411 BOARD=feather52840 all +Create firmware.uf2 +../../tools/uf2/utils/uf2conv.py -f 0xADA52840 -c -o "build-feather52840-s140/firmware.uf2" "build-feather52840-s140/firmware.hex" +Converting to uf2, output size: 392192, start address: 0x26000 +Wrote 392192 bytes to build-feather52840-s140/firmware.uf2. +``` + +Simply drag and drop firmware.uf2 to the MSC, the nrf52840 will blink fast and reset after done. diff --git a/ports/nrf/boards/TG-Watch02A/board.c b/ports/nrf/boards/TG-Watch02A/board.c new file mode 100644 index 000000000..4421970ee --- /dev/null +++ b/ports/nrf/boards/TG-Watch02A/board.c @@ -0,0 +1,38 @@ +/* + * This file is part of the MicroPython project, http://micropython.org/ + * + * The MIT License (MIT) + * + * Copyright (c) 2017 Scott Shawcroft for Adafruit Industries + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#include "boards/board.h" + +void board_init(void) { +} + +bool board_requests_safe_mode(void) { + return false; +} + +void reset_board(void) { + +} diff --git a/ports/nrf/boards/TG-Watch02A/mpconfigboard.h b/ports/nrf/boards/TG-Watch02A/mpconfigboard.h new file mode 100644 index 000000000..27bebec64 --- /dev/null +++ b/ports/nrf/boards/TG-Watch02A/mpconfigboard.h @@ -0,0 +1,72 @@ +/* + * This file is part of the MicroPython project, http://micropython.org/ + * + * The MIT License (MIT) + * + * Copyright (c) 2016 Glenn Ruben Bakke + * Copyright (c) 2018 Dan Halbert for Adafruit Industries + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#include "nrfx/hal/nrf_gpio.h" + +#define MICROPY_HW_BOARD_NAME "TG-Watch02A-rev00" +#define MICROPY_HW_MCU_NAME "nRF52840" + +#define FLASH_SIZE (0x100000) +#define FLASH_PAGE_SIZE (4096) + +#define MICROPY_HW_NEOPIXEL (&pin_P0_16) + +#define MICROPY_HW_LED_STATUS (&pin_P1_15) + +#if QSPI_FLASH_FILESYSTEM +#define MICROPY_QSPI_DATA0 NRF_GPIO_PIN_MAP(0, 17) +#define MICROPY_QSPI_DATA1 NRF_GPIO_PIN_MAP(0, 22) +#define MICROPY_QSPI_DATA2 NRF_GPIO_PIN_MAP(0, 23) +#define MICROPY_QSPI_DATA3 NRF_GPIO_PIN_MAP(0, 21) +#define MICROPY_QSPI_SCK NRF_GPIO_PIN_MAP(0, 19) +#define MICROPY_QSPI_CS NRF_GPIO_PIN_MAP(0, 20) +#endif + +#if SPI_FLASH_FILESYSTEM +#define SPI_FLASH_MOSI_PIN &pin_P0_17 +#define SPI_FLASH_MISO_PIN &pin_P0_22 +#define SPI_FLASH_SCK_PIN &pin_P0_19 +#define SPI_FLASH_CS_PIN &pin_P0_20 +#endif + +#define CIRCUITPY_AUTORELOAD_DELAY_MS 500 + +#define CIRCUITPY_INTERNAL_NVM_SIZE (4096) + +#define BOARD_FLASH_SIZE (FLASH_SIZE - 0x4000 - CIRCUITPY_INTERNAL_NVM_SIZE) + +#define BOARD_HAS_CRYSTAL 0 + +#define DEFAULT_I2C_BUS_SCL (&pin_P0_11) +#define DEFAULT_I2C_BUS_SDA (&pin_P0_12) + +#define DEFAULT_SPI_BUS_SCK (&pin_P0_14) +#define DEFAULT_SPI_BUS_MOSI (&pin_P0_13) +#define DEFAULT_SPI_BUS_MISO (&pin_P0_15) + +#define DEFAULT_UART_BUS_RX (&pin_P0_24) +#define DEFAULT_UART_BUS_TX (&pin_P0_25) diff --git a/ports/nrf/boards/TG-Watch02A/mpconfigboard.mk b/ports/nrf/boards/TG-Watch02A/mpconfigboard.mk new file mode 100644 index 000000000..718a7862d --- /dev/null +++ b/ports/nrf/boards/TG-Watch02A/mpconfigboard.mk @@ -0,0 +1,26 @@ +USB_VID = 0x239A +USB_PID = 0x802A +USB_PRODUCT = "TG-Watch02" +USB_MANUFACTURER = "TG-Tech + +MCU_SERIES = m4 +MCU_VARIANT = nrf52 +MCU_SUB_VARIANT = nrf52840 +MCU_CHIP = nrf52840 +SD ?= s140 +SOFTDEV_VERSION ?= 6.1.0 + +BOOT_SETTING_ADDR = 0xFF000 + +ifeq ($(SD),) + LD_FILE = boards/nrf52840_1M_256k.ld +else + LD_FILE = boards/adafruit_$(MCU_SUB_VARIANT)_$(SD_LOWER)_v$(firstword $(subst ., ,$(SOFTDEV_VERSION))).ld + CIRCUITPY_BLEIO = 1 +endif + +NRF_DEFINES += -DNRF52840_XXAA -DNRF52840 + +QSPI_FLASH_FILESYSTEM = 1 +EXTERNAL_FLASH_DEVICE_COUNT = 1 +EXTERNAL_FLASH_DEVICES = "GD25Q16C" diff --git a/ports/nrf/boards/TG-Watch02A/pins.c b/ports/nrf/boards/TG-Watch02A/pins.c new file mode 100644 index 000000000..ec2689ab4 --- /dev/null +++ b/ports/nrf/boards/TG-Watch02A/pins.c @@ -0,0 +1,53 @@ +#include "shared-bindings/board/__init__.h" + +STATIC const mp_rom_map_elem_t board_module_globals_table[] = { + { MP_ROM_QSTR(MP_QSTR_A0), MP_ROM_PTR(&pin_P0_04) }, + { MP_ROM_QSTR(MP_QSTR_A1), MP_ROM_PTR(&pin_P0_05) }, + { MP_ROM_QSTR(MP_QSTR_A2), MP_ROM_PTR(&pin_P0_30) }, + { MP_ROM_QSTR(MP_QSTR_A3), MP_ROM_PTR(&pin_P0_28) }, + { MP_ROM_QSTR(MP_QSTR_A4), MP_ROM_PTR(&pin_P0_02) }, + { MP_ROM_QSTR(MP_QSTR_A5), MP_ROM_PTR(&pin_P0_03) }, + + { MP_ROM_QSTR(MP_QSTR_AREF), MP_ROM_PTR(&pin_P0_31) }, + + { MP_ROM_QSTR(MP_QSTR_VOLTAGE_MONITOR), MP_ROM_PTR(&pin_P0_29) }, + { MP_ROM_QSTR(MP_QSTR_BATTERY), MP_ROM_PTR(&pin_P0_29) }, + + { MP_ROM_QSTR(MP_QSTR_SWITCH), MP_ROM_PTR(&pin_P1_02) }, + + { MP_ROM_QSTR(MP_QSTR_NFC1), MP_ROM_PTR(&pin_P0_09) }, + { MP_ROM_QSTR(MP_QSTR_NFC2), MP_ROM_PTR(&pin_P0_10) }, + + { MP_ROM_QSTR(MP_QSTR_D2), MP_ROM_PTR(&pin_P0_10) }, + { MP_ROM_QSTR(MP_QSTR_D5), MP_ROM_PTR(&pin_P1_08) }, + { MP_ROM_QSTR(MP_QSTR_D6), MP_ROM_PTR(&pin_P0_07) }, + { MP_ROM_QSTR(MP_QSTR_D9), MP_ROM_PTR(&pin_P0_26) }, + { MP_ROM_QSTR(MP_QSTR_D10), MP_ROM_PTR(&pin_P0_27) }, + { MP_ROM_QSTR(MP_QSTR_D11), MP_ROM_PTR(&pin_P0_06) }, + { MP_ROM_QSTR(MP_QSTR_D12), MP_ROM_PTR(&pin_P0_08) }, + { MP_ROM_QSTR(MP_QSTR_D13), MP_ROM_PTR(&pin_P1_09) }, + + { MP_ROM_QSTR(MP_QSTR_NEOPIXEL), MP_ROM_PTR(&pin_P0_16) }, + + { MP_ROM_QSTR(MP_QSTR_SCK), MP_ROM_PTR(&pin_P0_14) }, + { MP_ROM_QSTR(MP_QSTR_MOSI), MP_ROM_PTR(&pin_P0_13) }, + { MP_ROM_QSTR(MP_QSTR_MISO), MP_ROM_PTR(&pin_P0_15) }, + + { MP_ROM_QSTR(MP_QSTR_TX), MP_ROM_PTR(&pin_P0_25) }, + { MP_ROM_QSTR(MP_QSTR_RX), MP_ROM_PTR(&pin_P0_24) }, + + { MP_ROM_QSTR(MP_QSTR_SCL), MP_ROM_PTR(&pin_P0_11) }, + { MP_ROM_QSTR(MP_QSTR_SDA), MP_ROM_PTR(&pin_P0_12) }, + + { MP_ROM_QSTR(MP_QSTR_L), MP_ROM_PTR(&pin_P1_15) }, + { MP_ROM_QSTR(MP_QSTR_RED_LED), MP_ROM_PTR(&pin_P1_15) }, + { MP_ROM_QSTR(MP_QSTR_D3), MP_ROM_PTR(&pin_P1_15) }, + + { MP_ROM_QSTR(MP_QSTR_BLUE_LED), MP_ROM_PTR(&pin_P1_10) }, + + { MP_ROM_QSTR(MP_QSTR_UART), MP_ROM_PTR(&board_uart_obj) }, + { MP_ROM_QSTR(MP_QSTR_SPI), MP_ROM_PTR(&board_spi_obj) }, + { MP_ROM_QSTR(MP_QSTR_I2C), MP_ROM_PTR(&board_i2c_obj) }, +}; + +MP_DEFINE_CONST_DICT(board_module_globals, board_module_globals_table); diff --git a/ports/nrf/boards/pca10056/mpconfigboard.h b/ports/nrf/boards/pca10056/mpconfigboard.h index 5b30c7fe8..8cc3ad8c2 100644 --- a/ports/nrf/boards/pca10056/mpconfigboard.h +++ b/ports/nrf/boards/pca10056/mpconfigboard.h @@ -5,6 +5,7 @@ * * Copyright (c) 2016 Glenn Ruben Bakke * + * * Permission is hereby granted, free of charge, to any person obtaining a copy * of this software and associated documentation files (the "Software"), to deal * in the Software without restriction, including without limitation the rights |