diff options
Diffstat (limited to 'docs/library/pyb.UART.rst')
| -rw-r--r-- | docs/library/pyb.UART.rst | 245 |
1 files changed, 0 insertions, 245 deletions
diff --git a/docs/library/pyb.UART.rst b/docs/library/pyb.UART.rst deleted file mode 100644 index 76f347ffa..000000000 --- a/docs/library/pyb.UART.rst +++ /dev/null @@ -1,245 +0,0 @@ -.. currentmodule:: pyb -.. _pyb.UART: - -class UART -- duplex serial communication bus -============================================= - -UART implements the standard UART/USART duplex serial communications protocol. At -the physical level it consists of 2 lines: RX and TX. The unit of communication -is a character (not to be confused with a string character) which can be 8 or 9 -bits wide. - -UART objects can be created and initialised using:: - - from pyb import UART - - uart = UART(1, 9600) # init with given baudrate - uart.init(9600, bits=8, parity=None, stop=1) # init with given parameters - -.. only:: port_pyboard - - Bits can be 7, 8 or 9. Parity can be None, 0 (even) or 1 (odd). Stop can be 1 or 2. - - *Note:* with parity=None, only 8 and 9 bits are supported. With parity enabled, - only 7 and 8 bits are supported. - -A UART object acts like a stream object and reading and writing is done -using the standard stream methods:: - - uart.read(10) # read 10 characters, returns a bytes object - uart.read() # read all available characters - uart.readline() # read a line - uart.readinto(buf) # read and store into the given buffer - uart.write('abc') # write the 3 characters - -.. only:: port_pyboard - - Individual characters can be read/written using:: - - uart.readchar() # read 1 character and returns it as an integer - uart.writechar(42) # write 1 character - - To check if there is anything to be read, use:: - - uart.any() # returns the number of characters waiting - - - *Note:* The stream functions ``read``, ``write``, etc. are new in MicroPython v1.3.4. - Earlier versions use ``uart.send`` and ``uart.recv``. - -Constructors ------------- - -.. only:: port_pyboard - - .. class:: pyb.UART(bus, ...) - - Construct a UART object on the given bus. ``bus`` can be 1-6, or 'XA', 'XB', 'YA', or 'YB'. - With no additional parameters, the UART object is created but not - initialised (it has the settings from the last initialisation of - the bus, if any). If extra arguments are given, the bus is initialised. - See ``init`` for parameters of initialisation. - - The physical pins of the UART busses are: - - - ``UART(4)`` is on ``XA``: ``(TX, RX) = (X1, X2) = (PA0, PA1)`` - - ``UART(1)`` is on ``XB``: ``(TX, RX) = (X9, X10) = (PB6, PB7)`` - - ``UART(6)`` is on ``YA``: ``(TX, RX) = (Y1, Y2) = (PC6, PC7)`` - - ``UART(3)`` is on ``YB``: ``(TX, RX) = (Y9, Y10) = (PB10, PB11)`` - - ``UART(2)`` is on: ``(TX, RX) = (X3, X4) = (PA2, PA3)`` - - The Pyboard Lite supports UART(1), UART(2) and UART(6) only. Pins are as above except: - - - ``UART(2)`` is on: ``(TX, RX) = (X1, X2) = (PA2, PA3)`` - -Methods -------- - -.. only:: port_pyboard - - .. method:: UART.init(baudrate, bits=8, parity=None, stop=1, \*, timeout=1000, flow=0, timeout_char=0, read_buf_len=64) - - Initialise the UART bus with the given parameters: - - - ``baudrate`` is the clock rate. - - ``bits`` is the number of bits per character, 7, 8 or 9. - - ``parity`` is the parity, ``None``, 0 (even) or 1 (odd). - - ``stop`` is the number of stop bits, 1 or 2. - - ``flow`` sets the flow control type. Can be 0, ``UART.RTS``, ``UART.CTS`` - or ``UART.RTS | UART.CTS``. - - ``timeout`` is the timeout in milliseconds to wait for writing/reading the first character. - - ``timeout_char`` is the timeout in milliseconds to wait between characters while writing or reading. - - ``read_buf_len`` is the character length of the read buffer (0 to disable). - - This method will raise an exception if the baudrate could not be set within - 5% of the desired value. The minimum baudrate is dictated by the frequency - of the bus that the UART is on; UART(1) and UART(6) are APB2, the rest are on - APB1. The default bus frequencies give a minimum baudrate of 1300 for - UART(1) and UART(6) and 650 for the others. Use :func:`pyb.freq <pyb.freq>` - to reduce the bus frequencies to get lower baudrates. - - *Note:* with parity=None, only 8 and 9 bits are supported. With parity enabled, - only 7 and 8 bits are supported. - -.. method:: UART.deinit() - - Turn off the UART bus. - -.. only:: port_pyboard - - .. method:: UART.any() - - Returns the number of bytes waiting (may be 0). - -.. method:: UART.read([nbytes]) - - Read characters. If ``nbytes`` is specified then read at most that many bytes. - If ``nbytes`` are available in the buffer, returns immediately, otherwise returns - when sufficient characters arrive or the timeout elapses. - - If ``nbytes`` is not given then the method reads as much data as possible. It - returns after the timeout has elapsed. - - .. only:: port_pyboard - - *Note:* for 9 bit characters each character takes two bytes, ``nbytes`` must - be even, and the number of characters is ``nbytes/2``. - - Return value: a bytes object containing the bytes read in. Returns ``None`` - on timeout. - -.. method:: UART.readchar() - - Receive a single character on the bus. - - Return value: The character read, as an integer. Returns -1 on timeout. - -.. method:: UART.readinto(buf[, nbytes]) - - Read bytes into the ``buf``. If ``nbytes`` is specified then read at most - that many bytes. Otherwise, read at most ``len(buf)`` bytes. - - Return value: number of bytes read and stored into ``buf`` or ``None`` on - timeout. - -.. method:: UART.readline() - - Read a line, ending in a newline character. If such a line exists, return is - immediate. If the timeout elapses, all available data is returned regardless - of whether a newline exists. - - Return value: the line read or ``None`` on timeout if no data is available. - -.. method:: UART.write(buf) - - .. only:: port_pyboard - - Write the buffer of bytes to the bus. If characters are 7 or 8 bits wide - then each byte is one character. If characters are 9 bits wide then two - bytes are used for each character (little endian), and ``buf`` must contain - an even number of bytes. - - Return value: number of bytes written. If a timeout occurs and no bytes - were written returns ``None``. - -.. only:: port_pyboard - - .. method:: UART.writechar(char) - - Write a single character on the bus. ``char`` is an integer to write. - Return value: ``None``. See note below if CTS flow control is used. - -.. method:: UART.sendbreak() - - Send a break condition on the bus. This drives the bus low for a duration - of 13 bits. - Return value: ``None``. - -Constants ---------- - -.. only:: port_pyboard - - .. data:: UART.RTS - .. data:: UART.CTS - - to select the flow control type. - -Flow Control ------------- - -.. only:: port_pyboard - - On Pyboards V1 and V1.1 ``UART(2)`` and ``UART(3)`` support RTS/CTS hardware flow control - using the following pins: - - - ``UART(2)`` is on: ``(TX, RX, nRTS, nCTS) = (X3, X4, X2, X1) = (PA2, PA3, PA1, PA0)`` - - ``UART(3)`` is on :``(TX, RX, nRTS, nCTS) = (Y9, Y10, Y7, Y6) = (PB10, PB11, PB14, PB13)`` - - On the Pyboard Lite only ``UART(2)`` supports flow control on these pins: - - ``(TX, RX, nRTS, nCTS) = (X1, X2, X4, X3) = (PA2, PA3, PA1, PA0)`` - - In the following paragraphs the term "target" refers to the device connected to - the UART. - - When the UART's ``init()`` method is called with ``flow`` set to one or both of - ``UART.RTS`` and ``UART.CTS`` the relevant flow control pins are configured. - ``nRTS`` is an active low output, ``nCTS`` is an active low input with pullup - enabled. To achieve flow control the Pyboard's ``nCTS`` signal should be connected - to the target's ``nRTS`` and the Pyboard's ``nRTS`` to the target's ``nCTS``. - - CTS: target controls Pyboard transmitter - ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - - If CTS flow control is enabled the write behaviour is as follows: - - If the Pyboard's ``UART.write(buf)`` method is called, transmission will stall for - any periods when ``nCTS`` is ``False``. This will result in a timeout if the entire - buffer was not transmitted in the timeout period. The method returns the number of - bytes written, enabling the user to write the remainder of the data if required. In - the event of a timeout, a character will remain in the UART pending ``nCTS``. The - number of bytes composing this character will be included in the return value. - - If ``UART.writechar()`` is called when ``nCTS`` is ``False`` the method will time - out unless the target asserts ``nCTS`` in time. If it times out ``OSError 116`` - will be raised. The character will be transmitted as soon as the target asserts ``nCTS``. - - RTS: Pyboard controls target's transmitter - ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - - If RTS flow control is enabled, behaviour is as follows: - - If buffered input is used (``read_buf_len`` > 0), incoming characters are buffered. - If the buffer becomes full, the next character to arrive will cause ``nRTS`` to go - ``False``: the target should cease transmission. ``nRTS`` will go ``True`` when - characters are read from the buffer. - - Note that the ``any()`` method returns the number of bytes in the buffer. Assume a - buffer length of ``N`` bytes. If the buffer becomes full, and another character arrives, - ``nRTS`` will be set False, and ``any()`` will return the count ``N``. When - characters are read the additional character will be placed in the buffer and will - be included in the result of a subsequent ``any()`` call. - - If buffered input is not used (``read_buf_len`` == 0) the arrival of a character will - cause ``nRTS`` to go ``False`` until the character is read. |